Healthrider HRTL14911 TROUBLE-SHOOTING and Maintenance, Problemsolution, Power does not turn on

Page 25
Rear Roller Adjustment Bolts

TROUBLE-SHOOTING AND MAINTENANCE

Most treadmill problems can be solved by following the instructions below. If further assistance is needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEMSOLUTION

1.The power does not turn on

a.Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that meets all of the specifications described on page 7. Important: The treadmill is not compatible with GFCI-equipped outlets.

b.Make sure that the key is fully inserted into the console.

c.Check the circuit breaker located on the frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d.Check the on/off switch located on the frame near the power cord. The switch must be in the on posi- tion.

c

Tripped Reset

d

On

Position

2.The power turns off during use

a.Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in.

c.Remove the key from the console and then reinsert it.

d.Unplug the power cord, wait for five minutes, and then plug the power cord back in.

e.Make sure that the on/off switch is in the on position (see 1. d. above).

3.The walking belt slows when walked on

a.Use only a single-outlet surge suppressor that meets all of the specifications de- scribed on page 7.

b.If the walking belt is overtightened, tread-

mill performance may decrease and the b3–4”

walking belt may be permanently dam-

aged. Remove the key and UNPLUG THE POWER CORD. Using the included allen wrench, turn both rear roller adjustment

bolts counterclockwise 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift the edges of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking

belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

25

Image 25
Contents Model No. HRTL14911 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Back Before YOU BeginRight Side Assembly Treadmill Operation HOW to Plug in the Power CordPerformant Lubetm Walking Belt Features of the Console Description of the Console HOW to Turn on the Power HOW to USE the Manual ModePulse/Calories Time/Segment TimeDistance/Incline Select one of the six preset programs HOW to USE the Preset ProgramsHOW to USE the Pulse Programs Enter a maximum heart rate setting Select one of the two custom programs HOW to Create Custom ProgramsHOW to USE Custom Programs HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAudio Adapter Cable HOW to Connect Your VCRPressVCR. the Play button on your CD player or Whenkey. the program is completed, remove Follow the on-line instructions to start the program HOW to USE Programs Directly from OUR WEB SiteOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problemsolution TROUBLE-SHOOTING and MaintenancePower does not turn on Power turns off during useDisplays Walking belt is off-center or slips when walked onTop Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key Qty Description R0202AHOW to Order Replacement Parts Drawing ExplodedExploded DRAWING-Model No. HRTL14911 Limited Warranty