NordicTrack NTTL11993 user manual Do not tighten the Bolts yet

Page 7

4.Place one of the Handrail Spacers (65) on the right Upright (69) as shown, with the cutout toward the tread- mill (see inset drawing A). Pull the Upright Wire Harness (98) up through the Handrail Spacer. Place the other Handrail Spacer on the left Upright (not shown).

Have a second person hold the Handrails (66) near the Uprights (69) as shown. Connect the Upright Wire Harness (98) to the wires extending from the right Handrail. Insert the connectors and the Wire Harness

(98)into the hole in the Console Base (81) (see inset drawing B).

Be careful not to pinch the Wire Harness (98) as you set the Handrails (66) on the Spacers (65).

5.Insert two Handrail Bushings (75) into the right Upright

(69).Turn the Handrail Bushings so they fit against the Upright with the thick sides of the Bushings facing the center of the treadmill as shown in the inset drawing.

Insert two Handrail Bolts (78) with Handrail Washers

(77)into the Handrail Bushings (75), the right Upright (69), and the right Handrail Spacer (65). Lift up the right Handrail (66) to align the Bolts with the holes in the Handrail. Next, thread the Bolts into the Handrail (66).

Do not tighten the Bolts yet.

Attach the left Handrail (not shown) in the same way. Tighten all four Handrail Bolts (78).

6.Look at the Endcap (58). If the left or right foot on the Endcap does not touch the floor, the included thick base pads should be attached to the treadmill as de- scribed below.

Refer to assembly step 3. Lower the treadmill frame and the Uprights (69) as shown. If the left foot of the Endcap (58) was off the ground, remove the two Base Pads (99) from the right Upright (69). Attach the in- cluded thick base pads to the Upright. If the right side of the Endcap was off the ground, attach the thick base pads to the left Upright.

Note: If either side of the Endcap (58) lifts off the floor when the treadmill is used, attach the thick base pads as described.

4

Cutout

A

 

 

 

81

 

 

 

 

66

 

 

69

 

 

 

 

 

 

 

 

65

 

98 69

B

98

 

 

65

 

 

 

 

 

 

 

81

5

 

 

 

 

 

 

66

 

 

 

65

 

 

 

 

69

 

 

 

 

75

 

Thick

 

 

 

77

 

 

 

Side

 

 

 

 

 

75

 

 

 

 

77

 

78

 

6

 

 

 

 

Left

 

 

 

 

Foot

58

 

 

 

 

 

 

 

 

 

 

 

Left

 

 

 

 

Foot

7.Make sure that all parts are tightened before you use the treadmill. Note: If there is a thin sheet of clear plastic on the face of the hood decal and the ÒComforTrackÓ decal, remove it. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or car- pet from damage, place a mat under the treadmill.

7

Image 7
Contents Model No. NTTL11993 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Left Side Before YOU BeginRight Side Your own phillips screwdriver and wire cutters AssemblyDo not tighten the Bolts yet HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console Attach the clip to the waistband of your clothes Move the on/off switch to the on positionEnter your weight Getting StartedHOW to USE the Manual Mode HOW to USE Preset Programs Follow your progress with the displays When the program has ended, remove the keyHOW to Create Custom Programs HOW to USE Custom Programs Select the fitness test program HOW to USE the Fitness Test ProgramSor to use the fitness test program see Put on the chest pulse sensorSelect the pulse-driven program HOW to USE the PULSE-DRIVEN ProgramFollow your progress with the displays HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoHOW to Connect Your VCR Whenkey. the program is completed, remove Follow your progress with the LED track and the displaysSelect a program HOW to USE Programs Directly from OUR Internet SiteGo to your computer and start an internet Connection Start your web browser, if necessaryOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TROUBLE-SHOOTINGTop View 3ÓÐ4Ó Problem The walking belt slows when walked onExercise Intensity Conditioning GuidelinesWorkout Guidelines Suggested Stretches Qty Description Part LISTÑModel No. NTTL11993Ordering Replacement Parts Exploded DRAWINGÑModel No. NTTL11993 108 111 115 117 9087 104 100 102 106 103 107 105 99 100 Limited Warranty