ParaBody 503 manual TURN. see Detail, CAPS. see Detail B AS Much SPI~LING AS Possible

503EXS00 PEG DEC ATTACHMENTA~5~.E_M.J:$LY-I~STR.UL'I'IO~NS

(STEe#2) ¯ ¯ ..... ~.I-~

THE ~RU~IONS FOR ~EP ~2 ARk T0 BE USED'WITH D~G SHEET ~! OF

1.Loosely ~cmble one (I) 3/8 DIA. X 1 IN. LG. BUSH~GPULLEY ~d 0n~ (1) CABLE

2.

CL~ to ~e PULLEY FLAT on ~e WEIGHT STACK S~PORT BASE, (CON~ION PO~ #3), using one (1) 3/8 X 1-3/4 BOLT, one (1) 3/8 LOCKWASHE~~d one (1) 3/8 ~. (SEE

A).

ASSEMBLE~e SWIVEL PULLEY B~C~TS using (1) 3/8 DIA x 3/4 BOLT, (2) ~/16 WAS~,

(1)3/8 WASHER~d (1) 3/8 LOCK NUT. ~IGHTEN UNTIL LOC~D, THEN'BACK O~

TURN.) (SEE DETAIL '

3.LOOSELYa~ach m'o (2) 3/8 DIA. X 1 IN. LG. BUSHINGPULLEYSMto ~e PULLEYE'.~C~T.- ASSEMBLY,using ~vo (2) 3/8 X 1-1~ BOLTS, four (4) CAP WAS~RS,~o (2) 3/8 ~S

(4)CAPS. (SEE DETAIL "B")

NOTE: BEFORE PROCEEDING WITH CABLE INSTALLATION, UNtiL CABLE, AND .REMO~

AS MUCH SPI~LING AS POSSIBLE.

4.~oute the PEC DEC LOOP CABLE ASSEMBLYthrough th~ top halfof~e PULLEYB~kC~T

ASSEMBLY.and securely a~ach each CABLEEND to cnch CAMon the LE~ and ~GHT PEC DEC ARMS,using two (2) 3 'l 6 X 1 BOLTS,FOUR(4) ~/16 WASHERS, ~vo (2) 5/16 LOCKWASHERS, two (2) ~/16 NUTS.

NOTE MAKESURE CABLE ENDS ~EST FLAT AGAINST THE INSIDE OF THE CAMS) (SEE DETAIL C AND PULLEY REFERENCE POINTS A, B, & C ON THE CABLE RO~ING-DIAG~M VIE~V OF THE ASSEMBLED PRODUCT

NOTE: POSITION THE CABLE RETAINING CLIPS O~ THE PULLEY B~CKET SUPPORT IN A VERTICAL POSITION AFTER PEC DEC LOOP CABLE ASSEMBLY HAS BEEN ROUTED, AND TIGHTEN SECURELY (SEE ASSEMBLY VIEW ON SHEET

SKIP SEOUENCE ~5 IF ASSEMBLING PEC DEC AND THE BASE U'NI~T THE SA~IE TI~E.

5.Disconnect the OLD SECONDARYCABLE ASSEMBLYat the LEG CURL ATTACHMENT CONNECTIONPOINT #4 (SEE DETAILD) and remove it by pulling it out from the LOWROW

PULLEYSTATION(CONNECTIONPOINT #5)	and discard. Loosen the bolt connection
PULLEY REFERENCE POINT H so that	the SECONDARYCABLE ASSEMBLIES (OLD & NEW

SWAPOUT)can be passed under the CABLERETAINERCLIP.

5.

,

.....

Reroute the new SECONDARYSWAPOUTCABLEASSE.MBLYb.v starting at PULLEYreference point D on the CABLEROUTINGDIAGRAM.Continue to pass the CABLEASSEMBLYover PULLEYSREFERENCEPOINTS E, F. G, & H, and reartach the CABLEend to the LEG CURL EXTENSION CAM as shown in DETAIL D. (MAKE SURE CABLE END RESTS FLAT ON THE

CAM)Re ti,_,hten the [',.~'.t connections at PULLEYREFERENCEPOINTSH (ADJUSTABI'.EPRE STRE~ECH~LIELEI-~-'- F..~-P U LLEYFLA:I'.na. the-WEt.G HI.~TACK.SUPPORT-BASE-).

TIGHTEN all PULLEY CONNECTIONS.