Bodysmith Workout CENTER. Assembly Instructions

807 BODYSMITH WORKOUT CENTER. ASSEMBLY INSTRUCTIONS

SECURELYassemble the BENCHFRAMEto the UPRIGHTFRAMEas shown on drawing, using two

(2)3/8 X 3 IN. BOLTSone. (I) 3/8 X 2-3/4 IN. BOLT,six (6) 3/8 IN. WASHERS,and th:ee (31

LOCK NUTS.

Attach eight (8) PARAGLIDESTRIPS to both UPRIGHTTUBESon the UPRIGHTFRAME(FOUR FOREACHUPRIGHT)as shown in (DETAILA) using the following steps:

I0.

.11.

¯Thoroughlyclean all surfaces where the PARAGLIDESTRIPSare to be attached.

Removethe PARAGLIDESTRIPSfrom the paper bacldng and firmly apply them to all shown surfaces.

Attach eight (8) PARAGLIDESTRIPSto the bottom of both SADDLESas shmvn in (DETAILC) using the steps outlined in STEP9

Slide two (2) I-1/4 X 5 IN. GRIPSover the DIP HANDLESof both SADDLES(IF. A LUBRICANT REQUIRED, COAT THE INSIDE OF THE GRIP WITH RUBBING ALCOHOL)

12.Pull back tile SPRINGPIN on the UPRIGHTTUBES,and insert the SADDLESas showr, on drawing. Slide the SADDLEdownto the desired height and release the SPRINGPIN into the hole.

13.Secure the SADDLESin place with two (2) THUMBSCREWSasshown on drawing.

14.Attach two (2) THUMBSCREWStothe DIP TUBESon the UPRIGHTFRAMEas shown on drawing. Whenready to perform the DIP EXERCISE,simply insert the SADDLESinto the DIP TUBESand tighten the two (2) THUMBSCREWS.

15.To assemble the SEATPADto the WOLFFSLEEVE,start by sliding two (2) HINGETABSover the PIN of the WOLFFSLEEVE(ONE ONEACHSIDE) as shown on drawing, and SECUIRELYassemble each HINGETABto the SEATPADusing two (2) 3/8 X 1 IN. BOLTS,two (2) 3/8 IN. WASHERS,and two (2) 3/8 IN. WASHERS.(MAKESURE BOTHHINGE TABS ARF. ALL THE WAYON THE PIN)

16.To assemble the BACKPADto the WOLFFSLEEVE,slide the two (2) remaining HINGETABSover the PIN of the WOLFFSLEEVE(ONE ONEACHSIDE) as shown on drawing, and SECURELY assemble each HINGETABto the BACKPADusing two (2) 3/8 X I IN. BOLTS,two (2) 3/8 IN. LOCI(

	WASHERS,and	two	(2) 3/8 IN. WASHERS.(MAKESURE BOTHHINGE TABS ARE	¯
	AGAINST THE OTHER HINGES)
t7.	Insert one (I)	I-3/4	IN. SQ. ENDCAPinto the top of the LEGEXTENSIONNECKas skown
	drawing.

18.Slide two (2) ROLLERPADSover each end of the SHAFTof the LEGEXTENSIONNECK,as shown on drawing, and hold in place using two (2) STARLOCI( COLLARS.

19.Insert three (3) 1-3/4 IN. SQ. ENDCAPSinto the ends of the LEGEXTENSIONas shown on drawing.

20.Insert two (2) 1/2 IN. FLANGEBEARINGSinto the BUSHINGon the LEGEXTENSIONas shown drawin,z.