ParaBody ex 350 manual IN. Locknut, TOP SECTION. Remove Pulley for Ease of Installation, Support

358 EX350 ASSEMBLY INSTRUCTIONS

LOOSELYassemble one (1) 3 I/20.D. on the LEGCURLARMASSEMBLY.....

IN. LOCKNUT.

DIA. PULLEYwith I IN. BUSHINGinto PULLEYBRACKET Using one (1) 3/8 X 2 IN. HEXHEADBOLTand one (1)

37.Attach two (2) ROLLERPADS to the LEG CURLARMASSEMBLYusing. one (I) ROLLER SHAFT. and two (2; STAR LOCK COLLARS. (NOTE: WHENUSING THE LOWPULLEY OFF THE LEG CURL ARM ASSEMBLY, LOCK IN PLACE BY INSERTING L-PIN INTO BUSHING ON THE LEG CURL EXTENSION NECK)

38.Assemble two (2} ROLLERPADS to the BACKSEAT SUPPORT.using one (1)'ROLLER SHAFT. and two (2) STAR LOCKCOLLARS.

39.A~tach one (i) 3-1 20.D. DIA. PULLEYwith I IN. BUSHINGinto REAR"U" PULLEYBRACKET of BACK/SEATSUPPORT.using one (I) 3/8 X I-3/4 IN. HEXHEADBOLTand one (1) 3/8

LOCKNUT.

~

.40

Attach BACKPADto BACK/SEATSUPPORT,using two (2) 3,'8 X 3 IN. HEXHEADBOLTSand two

(2).3.'8 IN. LOCKWASHERS.(NOTE: HIDEM WELTCLIP SHOULDBE LOCATED BOTTOM)

***REFER TO ASSEMBLYDRAWINGo#3FOR STEPS 41 THRU 44 ***

41.Attach two (2) .~-iO.DI DI A. PULLEYS with 1 IN."BUSHING tothe CONNECTOR PLATES, usin g two (2) .3 '8 X 2 IN. HEXHE~A.DBOLTSand two (2) 3/8 IN. LOCKNUTS(DO NOTTIGHTEN)

¯42. Slide four (4) I X 8 in. GRIPSover each, end of the LATBAR. and LOWROWBAR." (NOTE:IF LUBRICANT IS REQUIRED. PARABODY RECOMMENDS THOROUGHLY COATING THE INSIDE OF THE GRIP WITH RUBBING ALCOHOL)

NOTE: BEFORE PROCEEDING WITH CABLE INSTALLATION, UNRAVEL CABLE, A~N'D REMOVE AS MUCHSPIRALING AS POSSIBLE.

To install	the PRIMARYCABLEinsert	end of CABLEwith	THREADEDFITTING into
GROOVEof	PULLEYUpwards between	PULLEY and LAT BAR HOLDERon MA][N UPRIGHT
TOP SECTION. (REMOVE PULLEY FOR EASE OF INSTALLATION)
¯ Pull CABLEdown until CLEVIS CONNECTORstops a.galnst			PULLEYand LAT BARHOLDER.

¯Run CABLEdo~,.n and under TOP PULLEYon PRESS ARM.then over PULLEYon BACK/SEAT.

SUPPORT.

Pull CABLEarotmJ PULLEYon BACK/~EATSUPPORTand towards the PRESS ARM. Run CABLEover BOTTOMPULLEYof PRESSARMand back. through the opening of the BACK¯ SEAT SUPPORT. to the SMALLPULLEY.

Wliil¢ pulIi~g.CABLE down o~er SMALLPULLEYon the~back of the BACK/SEATSUPPORT.

insert the CABLEEND arotmd one of the PULLEYSor" the PULLEY/PLATECONNECTOR........

ASSEMBLY.