Hoist Fitness RPL-5305 owner manual Hoist Fitness Systems General Maintenance Information

Page 48

OWNER'S MANUAL

HOIST FITNESS SYSTEMS

GENERAL MAINTENANCE INFORMATION

Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack Pins:

*Check all pieces for signs of visible wear or damage.

*Check springs in snap hooks and pull-pins for proper tension and alignment.

*If the spring sticks or has lost its rigidity, replace it immediately.

Upholstery:

*To ensure prolonged upholstery life and proper hygiene, all upholstered pads should be wiped down with a damp cloth after every workout.

*Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying. Avoid using any abrasive cleaners or cleaners not intended for use on vinyl.

*Replace ripped or warn upholstery immediately.

*Keep sharp or pointed objects clear of all upholstery.

Decals:

*Inspect and familiarize yourself with any safety warnings or other user information posted on each decal.

Nuts and Bolts:

*Inspect all nuts and bolts for any loosening and tighten if needed.

*Go through a re-tightening sequence periodically to ensure that all hardware is tensioned proper.

Anti-Skid Surfaces:

*These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery.

Belts and Cables:

*Hoist uses only high quality belt, and mil-spec cables.

*Visually inspect the belts and cables for fraying, cracking, peeling or discoloration.

*While the machine is not in use, carefully run your fingers along the belt or cable to feel for thinning or bulging areas.

*Replace belts and cables immediately at the first signs of damage or wear. Do not use equipment until belts or cables have been replaced.

Belt and Cable Tension:

*Referring to the Owners Manual, when belts or cables are used check all bolts attachments to be sure they are properly attached.

*Check slack in cables and re-adjust cable tension if needed.

Seat Sleeves, Guide Rods:

*Wipe down adjusting tubes with a dust free rag before applying lubricant.

*Lubricate seat sleeves and Guide Rods with a Silicon or Teflon based lubricant spray.

Linear Bearings:

*Referring to the Owners Manual carefully disassemble the bearing from its housing and place a finger full of light grease (lithium, super lube, etc.) into the inside of the bearing. Using your finger, press the grease into the ball-bearings and their tracks. repeat until the ball-bearing tracks are full of grease. Insert the shaft back into the bearing and wipe off excess grease.

PLEASE KEEP THIS FOR YOUR RECORDS

RPL-5305 ASSEMBLY

PAGE 42

Image 48
Contents RPL-5305 Addendum Frame Assembly Machine Adjustment Major Adjustment33 780mm Part List RPL-5305 PLATE-LOADED Decline Chest PressContents Instructions Tools RequiredThis page WAS Intentionally Left Blank Frame Assembly Hand Tighten Hardware Repeat Assembly for Opposite Side 1057 Frame Assembly 1758 Frame Assembly Hand Tighten Hardware Frame Assembly Frame Assembly Wrench Tighten Hardware Repeat Assembly for Opposite Side Wrench Tighten Hardware 7711 Wrench Tighten Hardware Repeat Assembly for Opposite Side TIE ROD END LH Frame Assembly Wrench Tighten Hardware Repeat Assembly for Opposite Side Wrench Tighten Hardware Frame Assembly Frame Assembly Frame Assembly Frame Assembly Frame Assembly Frame Assembly Machine Adjustment 33 780mm PRE-ASSEMBLY Decal Placement Decal Reference 021-0003334 021-0018022 021-0003230 021-0004032 021-0003689 Part List END CAP Aluminium Ø1.25 ID UNC Thin Nylock NUT WZ BZ = Black Zinc WZ = White Zinc HHB = Hex Head Bolt AbbreviationsBolt Sizing Chart Fhcs Shcs HHB 123 Bhcs Washer Sizing Chart 026-01M211T 1/4 Long Heavy Flanged Spacer Maintenance Schedule RoutineHoist Fitness Systems General Maintenance Information Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack PinsWeight Training Tips Enjoy your RPL-5305 Hoist Fitness SystemWeight Training Exercise LOG Hoist Fitness Systems Limited Lifetime Warranty