Spalding M316001 manual Backboard Mounting, Height Adjustment and Warning Label Placement

Page 15

BACKBOARD MOUNTING (continued)

 

 

 

OR

 

ATTACH A STEEL-FRAMED STYLE BACKBOARD (STYLE WILL VARY)

 

 

 

 

 

 

3. Attach backboard using hardware shown.

Folow instructions that are packaged with backboard for specific assembly details.

6

15 6

15

25

15

15

8

25

8

HEIGHT ADJUSTMENT AND WARNING LABEL PLACEMENT

 

 

 

 

NOTE:

TO ADJUST BACKBOARD:

Adhere WARNING label (20) in

 

 

a clearly visible place.

 

 

 

Position looped end of

 

 

 

 

 

crank onto hook as shown.

WARNING

 

REGULATION RIM HEIGHT

Rotate crank handle to

Read and

understand warnings listed

 

IS 10 FEET (3.05 m).

below before using this

product.

 

 

Failure to follow these

warnings may

7

 

result in serious injury and/or

raise or lower backboard

property damage.

 

 

 

for safe operation of the system.

 

 

 

 

Owner must ensure that all players know and follow these rules

 

 

Crank

• DO NOT HANG on the rim or any part of the system including

 

 

keep player's face away from the backboard, rim and net.

 

 

 

backboard, support braces or net.

 

 

 

 

• During play, especially when performing dunk type activities,

 

 

22

Serious injury could occur if teeth/face come in contact with

 

 

backboard, rim or net.

 

 

 

 

• Do not slide, climb, shake or play on base and/or pole.

 

 

• When adjusting height or moving system, keep hands and

 

 

Hook

fingers away from moving parts.

 

 

 

 

• Do not allow children to move or adjust system.

 

 

 

During play, do not wear jewelry (rings, watches, necklaces,

 

 

etc.). Objects may entangle in net.

 

 

 

 

• Keep organic material away from pole base. Grass, litter, etc.

 

 

 

could cause corrosion and/or deterioration.

 

 

 

 

• Check pole system for signs of corrosion (rust, pitting,

 

 

 

chipping) and repaint with exterior enamel paint. If rust has

 

10 ft.

 

penetrated through the steel anywhere, replace pole

 

 

immediately.

 

 

 

 

• Check system before each use for proper ballast, loose

 

(3.05 m)

 

hardware, excessive wear and signs corrosion and repair

 

 

before use.

 

 

 

 

 

• Check system before each use for instability.

 

 

 

 

• Never play on damaged equipment.

 

 

 

 

• Keep pole top covered with cap at all times.

 

 

 

 

• See instruction manual for proper installation and

 

 

 

maintenance.

 

 

 

 

 

In the U.S.: 1-800-558-5234

In the U.S.: 1-800-334-9111

 

 

 

In Canada: 1-800-284-8339

 

 

 

 

 

In the U.S.: 1-888-713-5488

In the U.S.: 1-800-558-5234

 

 

 

In Canada: 1-800-284-8339

 

 

 

ID#: 588000

05/05

 

 

 

15

 

 

01/07

ID# M316001

Image 15
Contents Universal Elevator Mount Safety Instructions Remove all contents from box Hardware Identifier Actual Size Bolts and Screws #12 Before YOU Start Assemble the Elevator Mount to a Square Pole Assemble the Elevator Mount to a Round Pole Assemble the Elevator Mount to a Wall or Flat Surface Assemble the Elevator Mount to a Flat or Angled Roof Flat or Angled Roof Section B Completed Assembly Style will Vary Attach a Composite Style BackboardBackboard Mounting Height Adjustment and Warning Label Placement