EVANSTONTM 6 TENT MODEL 2000001589
Before you begin
Read all instructions before set up.
•Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
•Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.
•Secure with all stakes and guylines provided to prevent property damage or personal injury.
•For best results in windy conditions, position narrow end of tent into the wind.
•Enlist the help of at least one other person to assist you when it is time to assemble the tent.
Pole Descriptions
Description | Qty. | Pole | Pole | Pole |
Dia. | Repair Kit | Replacement Kit | ||
Main Pole, black | 2 | 11mm | 501000539 | 501000549 |
Main Pole, grey | 1 | 11mm | 501000539 | 501000549 |
Rainfly Pole, black, long | 1 | 11mm | 501000539 | 501000549 |
Awning Pole, black, short | 1 | 6.9mm | 501000542 | 501000552 |
|
|
|
|
|
To Set Up Tent
1.Unfold tent and spread out on a clean, level surface with the door
facing the desired direction. (Fig. 1)
2. Assemble all poles by interlocking the
3. Insert black Main Poles through the black trimmed sleeves on top of tent forming an X”.
4.Insert grey Main Pole through grey trimmed sleeve, in front of tent. Make sure grey Main Poles overlap the black Main Poles. (Fig. 1)
LINE |
| Sleeves with Black Trim | Fig. 1 |
|
| ||
|
|
| |
STITCH | Grey, |
| Sleeve with |
Main Pole |
| Grey Trim | |
|
|
| |
|
| Door |
|
9. Attach frame clips along edges of tent |
| Fig. 3 |
to the black & grey Main Poles. |
|
|
|
| |
(Fig. 3) |
|
|
|
|
|
10.Stretch tent until taut, then secure metal loops located on both sides and four corners of tent with stakes. (Fig. 4)
Fig. 4
To Attach Rainfly
1.Drape Rainfly over tent with dark blue vestibule flaps located at the front of the tent. (Fig 5).
NOTE: Hook and loop fasteners, located on seams of underside of Rainfly, should be centered over black & grey Main Poles.
2.Insert the long, black, Rainfly Pole with through sleeve in underside of Rainfly above front door of tent. (Fig. 5)
Sleeve with Grey Trim
Rainfly
|
|
| Black, | |
|
|
| Rainfly Pole | |
|
|
|
|
|
| Door |
|
| |
Front of Tent |
|
| ||
| Fig. 5 | |||
Vestibule Flaps |
| |||
|
|
|
|
|
3.Insert short, black, thin Awning Pole through sleeve in underside of
Rainfly above window at back of tent. (Fig. 6)
4. Insert metal tip into grommet on tent seam at back of tent (Fig. 7). Go to opposite end of Awning Pole and gradually apply pressure to pole forming an arch; then insert metal tip into grommet.
Front of Tent |
Black, |
5. | Insert end of each black Main Pole into pins located in the corners |
| of the tent. (Fig. 2 & 2A) |
6. | Go to opposite end of each black Main Pole and gradually apply |
| pressure to each forming arches. Insert the pin into each pole end |
| at the corners of tent. (Fig. 2 & 2A) |
7. | Insert end of the grey Main Pole into pin located on the sides of the |
Rainfly Sleeve | Awning Pole |
| Back of Tent |
| Fig. 6 |
Grommet
Awning
Pole
Fig. 7
tent. (Fig. 2 & 2B) |
8. Go to opposite end of the grey Main Pole and gradually apply pres- |
sure to form an arch. Insert the pin into pole end at the side of tent. |
(Fig. 2 & 2B) |
Fig. 2
Door
Front of Tent
2A
2B
5. Insert end of each black Rainfly Pole into |
|
|
|
pin on either side of front door. (Fig. 8) |
|
|
|
6. Go to opposite end of Rainfly Pole and |
|
|
|
gradually apply pressure to form an arch. |
|
|
|
Insert the pin into pole end at other side of |
|
|
|
the door. (Fig. 8) |
|
|
|
7. Locate all hook & loop fasteners on under |
|
|
|
Fig. 8 |
|
| |
side of Rainfly and wrap around all Main |
|
| |
|
|
| |
Poles, Awning & Rainfly Pole to secure. |
|
|
|
Fig. 9 |
|
| |
(Fig. 9) |
|
| |
|
|
| |
|
|
| |
NOTE: Make sure longer hook & loop |
|
|
|
fastener on Rainfly is secured around grey |
|
|
|
and black Main Poles where they cross. |
|
|
|
(Fig. 10) |
|
|
|
|
|
|
|
|
|
| |
| Fig. 10 |
| |
|
|
|
|
(continued on other side)