JVC RX-558RBK manual Operating Other Components, Sound control section Amplifier, CD player, Tuner

Operating Other Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

English

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page 23) in addition to the connections using cables with RCA pin plugs (see page 5).

•Aim the remote control directly at the remote sensor on the receiver.

•If you use the buttons on the front panel to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using buttons on the remote control.

•Refer also to the manuals supplied with your components.

Sound control section (Amplifier)

After pressing SOUND CONTROL, you can perform the following operations:

SURROUND:	Selects the DSP modes.
CENTER – / +: Adjusts the center speaker output level for the
	Surround/DVD MULTI playback modes.
REAR•L – / +:	Adjusts the left/right rear speaker output level for
	the DSP modes.
	Adjusts the left rear speaker output level for the
	DVD MULTI playback mode.
REAR•R – / +:	Adjusts the right rear speaker output level for the
	DVD MULTI playback mode.
DELAY:	Selects the delay time of the rear speaker sound.
	(Only works when “PROLOGIC” is selected.)
EFFECT:	Selects the effect level for the DSP modes.
TEST:	Turns on or off the test tone output for the
	Surround mode.

Note:

CD	TV
TAPE/MD	DELAY
	1
FM/AM	EFFECT
	4	5
VCR
	7/P
DVD	SOUND
	CONTROL

DVD MULTI CD-DISC

PHONO TV/VIDEO

ONE TOUCH

OPERATION

VCR AUDIO

TEST SURROUND

2 5 3

– CENTER +

5	6	5
– REAR•L +

85 9

MENU

– REAR•R +

10 +10

ENT

TV VOL.

– +

TV CH

– +

After adjusting sounds, press the corresponding source selecting button or CD-DISC to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.

CD player

After pressing CD, you can perform the following operations on the CD player:

3:	Starts playing.
4:	Returns to the beginning of the current (or
¢:	previous) track.
	Skips to the beginning of the next track.

	+	+
MUTING	VOLUME	VCR CH
	–	–

7: Stops playing.

8: Pauses playing. To release it, press 3.

SLEEP

8

£PTY SEARCH

1 – 10, +10: Selects a track number directly.

For track number 5, press 5.

For track number 15, press +10, then 5.

4￿	￿4
1	1
PTY –	7 DISPLAY + PTY

RM - SR558RU REMOTE CONTROL

Tuner

After pressing FM/AM, you can perform the following operations:

FM/AM: Alternates between FM and AM (MW/LW).

1 – 10, +10: Selects a preset channel number directly. For channel number 5, press 5.

For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

PTY SEARCH: Searches for a program by PTY codes.

PTY – / +: Selects the PTY codes.

DISPLAY: Shows the RDS signals.

For track number 20, press +10, then 10.

CD player-changer

After pressing CD-DISC, you can perform the following operations on a CD player-changer:

3:	Starts playing.
4:	Returns to the beginning of the current (or
¢:	previous) track.
	Skips to the beginning of the next track.
7:	Stops playing.

8:Pauses playing. To release it, press 3.

1– 6, 7/P: Selects the number of a disc installed in a CD player-changer.

After pressing CD, you can perform the following operations on the CD player-changer:

1 – 10, +10: Selects a track number directly. For track number 5, press 5.

For track number 15, press +10, then 5. For track number 20, press +10, then 10.

For track number 30, press +10, +10, then 10.

24