Vision Fitness R1500 manual E P 4 Green BAG, E P 5 Black BAG, Pedals

A s s e m b l y
G u i d e	S T E P 6

R1500

SEMI-RECUMBENT FITNESS BIKE

To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.

If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.

Bottom Frame

Support Tube

S T E P 1 ORANGE BAG S T E P 1

•Connect bottom frame support tube to main frame with two (M8x15L) bolts and two (SW8) lock washers. Tighten

with the 5mm T-handle wrench.

S T E P 5		S T E P 4
Handlebar	Water Bottle	Console Mast
	Cage
		Console Mast
		Cover
		Console Mast
		Bracket

Heart Rate

Wires

S T E P 3 PINK BAG

•Connect the heart rate wires coming from the seat rail to the heart rate wires coming from the main frame.

•As you slide the seat rail onto the seat rail bracket, slide any excess heart rate wire into the seat rail bracket. Slide the seat rail on so the holes on the bottom of the bracket are in line with the frame. Insert three (M8x15L) bolts with three (SW8) lock washers into the holes for support. Do not tighten completely.

•Connect the bottom frame support tube to the bottom of the rear support foot with two (M8x20L) bolts and two (SW8) lock washers. Tighten with the 5mm T-handle wrench.

•Go back and tighten all bolts with the 5mm T-handle or 5mm L-shaped wrench.

S T E P 4 GREEN BAG

• Slide the console mast cover onto the

console mast.

• Wrap the wire tie that comes from the

bottom of the console mast around the

end of console cable and around the

heart rate wires that are sitting in the

frame console mast bracket. Slowly pull

the wire tie up through the console mast

until the cable and wires come through

the top of the mast. Slide the bottom of

the console mast over the frame mast

bracket. Holding the mast straight, insert

S T E P 2 BLUE BAG

• Attach rear support foot to the

bottom of the seat rail with four

(M8x15L) bolts and four (SW8) lock

washers. Do not tighten completely.

• Slide the seat frame onto the seat rail.

Make sure the flat side of the clamp

block rests against the bottom of the

seat rail. Also make sure the adjustment

handle is facing forward.

• Insert the heart rate wires located

under the seat frame through the hole

on the bottom of the seat rail and push

them toward the front of the rail. Take

the end of the heart rate wires that run

through the seat rail and insert them

through the hole in the bracket at the

end of the rail. Snap the wire grip

around the end of the heart rate wires

and snap it into place in the bracket.

	Seat Frame
	S T E P 2
	Seat Rail
Rear Support	Seat Rail
	Bracket
Foot
	Rubber Stopper
	Wire Grip

the (M8x10L) set screw into the front

side of the mast and tighten with the

4mm L-shaped wrench. Secure the mast

to the frame with four (M8x15L) bolts

and four (SW8) lock washers on the

sides of the mast and tighten with the

5mm T-handle wrench.

• Remove the four bolts from the back

side of the console. Plug the console

cable and heart rate wires into the back

side of the console. Place the console

onto the mounting plate of the console

mast and re-insert the four mounting

bolts. Tighten with the screwdriver.

• Remove the two bolts from the

backside of the console mast. Attach

the water bottle cage to the mast with

these two bolts. Tighten with the

screwdriver. Insert water bottle.

• Attach the rubber stopper to the
bottom of the seat rail with	the
(M5x10L) bolt. Tighten with	the
screwdriver.

S T E P 3

Heart Rate

S T E P 5 BLACK BAG

• Connect the Heart Rate wires from the

seat handlebar to the heart rate wires

S T E P 7 CONSOLE

• Refer to Product Selection and

Model Configuration decal on

console or follow these steps.

• Once the product is plugged in turn

S T E P 6	PEDALS
	• Attach left and right pedal straps to
	left and right pedals.
	• Attach left and right pedals to left
	and right crank arms. NOTE: both
	pedals and crank arms should be
	labeled left or right. Tighten with the
	included pedal wrench.	SIMPLE
	• Plug in power supply to power	DELUXE
	socket on the front side of the bike.	PREMIER

Wires

Heart Rate

Wires

from the seat frame. Attach seat

handlebar to seat frame with four

(M8x15L) bolts and four (SW8) lock

washers. Tighten with 5mm T-shaped

wrench.

• Attach seat bottom cushion to seat

frame with four (M6x35L) bolts and four

(M6) arc washers. Tighten with the

4mm L-shaped wrench.

• Attach the seat back cushion to the

seat frame with four (M6x35L) bolts and

four (M6) arc washers. Tighten with the

4mm L-shaped wrench.

on the console

• Select product (Bike (BK) or Elliptical

(EP)) using the resistance arrow keys.

Press ENTER to select.

• Select model number (Bike (1500,

2050, 2250, 3200) or Elliptical

(1500, 6000, 6200)) using the

RESISTANCE arrow keys. Press

ENTER to select. Console will reset to

start-up screen.

• The product selection and model

configuration is now complete.

CONSOLES