JVC CA-MXGT90, CA-MXGT80, CA-MXG70 manual Common Operations, Turning On or Off the Power

Page 12

Common Operations

Turning On or Off the Power

2 Turn 4/ ¢to adjust the hour, then press

To turn on the unit, press

STANDBY/ON so that the STANDBY lamp goes off.

To turn off the unit (on standby), press

STANDBY/ON again so that the STANDBY lamp lights up.

•The clock appears on the display (if Ecology Mode is not activated).

STANDBY/ON

STANDBY

STANDBY/ON

STANDBY

SET/DISPLAY.

The minute digits start flashing on the display.

• If you want to correct the hour after pressing SET/DISPLAY, press

CANCEL/DEMO.

The hour digits start flashing again.

•A little power is always consumed even while the unit is on standby.

To switch off the power supply completely, unplug the AC

power cord from the AC outlet.

When you unplug the AC power cord or if a power failure occurs

The clock is reset to “0:00” right away, while the tuner preset stations (see page 12) will be erased in a few days.

3 Turn 4/ ¢to adjust the minute, then press SET/DISPLAY.

To check the clock time

Press and hold SET/DISPLAY while playing any source.

•Each time you press and hold the button, the source indication and the clock time alternate on the display.

Saving the Power Consumption While on Standby — Ecology Mode

You can save the power consumption only while the unit is turned off (on standby).

To activate the Ecology Mode, press ECO. “ECO” appears and the display illumination (including the display demonstration) disappears from the display.

•Each time you press the button, “ECO” and “NORMAL” appear alternately on the display.

To deactivate the Ecology Mode, press ECO again. “NORMAL” appears and the display illumination appears on the display.

About Ecology Mode

•You can also activate and deactivate Ecology Mode while the unit is on, but it takes effect only when the unit is on standby.

•While Ecology Mode is activated, the display demonstration is canceled temporarily.

To adjust the clock again

If you have adjusted the clock before, you need to press CLOCK/TIMER repeatedly until the clock setting mode is selected.

•Each time you press the button, the clock/timer setting modes change as follows:

DAILY ON TIME REC

Canceled Clock ON TIME setting

(The hour digits start flashing.)

When you unplug the AC power cord or if a power failure occurs

The clock loses the setting and is reset to “0:00.” You need to set the clock again.

Selecting the Sources

To listen to the FM/AM broadcasts, press FM/AM.

(See page 12.)

To play back CDs, press CD 3´8. (See pages 13 – 16.) To play back tapes, press TAPE 23. (See page 17.)

To select the external equipment as the source, press AUX.

Setting the Clock

Before operating the unit any further, first set the clock built in this unit. You can set the clock whether the unit is on or off.

On the unit ONLY:

1 Press CLOCK/TIMER.

The hour digits start flashing on the display.

When you press the play button for a particular source (FM/AM, CD 3/8, TAPE 23, and AUX), the unit turns on (and the unit starts playing the source if it is ready

— COMPU PLAY CONTROL).

About the audio level indicator

All the audio level indicators light up when no signals come in.

– 9 –

Page 11 Page 13
Image 12
Page 11 Page 13
Contents CA-MXGT90/CA-MXGT80 CA-MXG70 Button in any position does not Class Laser Product Precautions IntroductionAbout This Manual Contents Location of the Buttons and Controls Front PanelFront Panel Become familiar with the buttons and controls on your unitDisplay Window See pages in the parentheses for details0Disc tray open/close CD1, CD2, and CD3 buttons 13, 14 Remote Control Remote ControlCD 3´8button 9, 14 Supplied Accessories Connecting Antennas Putting the Batteries into the Remote ControlGetting Started FM antennaConnecting Speakers Turn the AM loop antenna until you have the best receptionClose the speaker terminals AM antennaConnecting Other Equipment Canceling the Display DemonstrationOn the unit only To connect an analog componentTurning On or Off the Power Saving the Power Consumption While on Standby Ecology ModeSetting the Clock Common OperationsAdjusting the Volume To turn down the volume level temporarilyReinforcing the Bass Sound Selecting the Sound ModesCreating Your Own Sound Mode Manual Mode On the unit only Select one of the preset sound modesTo use your own sound mode Tuning in a Station Presetting StationsTuning in a Preset Station Listening to FM and AM BroadcastsPlaying Back CDs CD/CD-R/CD-RW Loading CDsPress the same 0 you have pressed in step Repeat steps 1 to 3 to place other CDsPlaying Back the Entire Discs Continuous Play Basic CD OperationsProgram Play Playing at Random Random Play Repeating Tracks or CDs Repeat PlayProhibiting Disc Ejection Tray Lock To exit from Random play mode, press Random againPlaying Back Tapes Playing Back a TapeLocating the Beginning of a Song Music Scan To clean the heads, capstans, and pinch rollers RecordingRecording a Tape on Deck B To protect your recordingTo record on both sides Reverse Mode Dubbing TapesCD Direct Recording Press DubbingAuto Edit Recording Using the Timers Using Daily TimerPress CLOCK/TIMER again How Daily Timer actually worksIf you have set the Daily Timer With the unit turned on When selecting Tuner FM or Tuner AMWhen selecting CD Turn 4/ ¢to set the volume levelUsing Recording Timer Select the preset stationHow Recording Timer actually works Unit enters preset station selecting modeUsing Sleep Timer Timer PriorityOn the remote control only Press Sleep Wait for about 5 seconds after specifying the time lengthMaintenance Cleaning the unitTo clean the disc Handling discsTroubleshooting SymptomSpecifications CA-MXG70 0401MWMMDWJEM Page Page
Top Page Image Contents