JVC RX-D206B manual Getting started, Before Installation, Putting batteries in the remote control

Page 6

Getting started

Before Installation

General precautions

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture and dust.

•The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

•Leave sufficient distance between the receiver and the TV.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

•When you are away on travel or otherwise for an extended period or time, remove the plug from the wall outlet. A small amount of power is always consumed while the power cord is connected to the wall outlet.

The receiver has a built-in cooling fan which operates while the receiver is turned on. Be sure to leave enough ventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power plug to the wall outlet until all

connections are completed.

Putting batteries in the remote control

Before using the remote control, put two supplied batteries first.

1

2

3

1Press and slide the battery cover on the back of the remote control.

2Insert batteries.

Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

•Supplied batteries are for initial setup. Replace for continued use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

When using the remote control, aim the remote control directly at the remote sensor on the front panel.

Remote sensor

Checking the supplied accessories

Check to be sure you have all of the following supplied accessories. If anything is missing, contact your dealer immediately.

•Remote control (⋅ 1)

•Batteries (⋅ 2)

•AM loop antenna (⋅ 1)

•FM antenna (⋅ 1)

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents RX-D205S / RX-D206B For Customer UseFor Canada/pour Le Canada For U.S.ADeclaration of Conformity Table of Contents Remote control When operating a DVD player, set the mode selector 1 to DVDParts identification Display window Rear panelFront panel Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedAM antenna connection Connecting the FM and AM antennasWire not supplied FM antenna connectionConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferTurn off all components before making connections Connecting video componentsConnecting a DVD recorder or DVD player RedBlue RedComponent video cable not supplied Green Blue Red Connecting a DBS tunerConnecting a TV Video cableUSB connection How to install the USB driversConnect the unit to the PC using a USB cable not supplied Digital connectionCheck if the drivers are correctly installed Connecting the power cordUSB drivers are installed automatically Now the PC is ready for playback through the USB connectionTo turn off the power into standby Turn on the powerSelecting the analog or digital input mode Basic operationsInitial setting Digital Auto Adjust the volumeListening with headphones Ex. When Dolby Digital is selectedSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyPress SET Basic settingsPress Setting 0chBasic setting items Speakers channels number and the sizeRoom size and the speaker distance/output level Setting the surround back speakers-S Back OUT Setting the speakersSetting subwoofer information-SUBWOOFER Turn Multi JOG to select the appropriate SettingFrom the remote control Activating the EX/ES/PLIIx setting- EX/ES/PLIIxSetting the speaker distance AutoSetting the crossover frequency-CROSSOVER Setting bass soundSetting subwoofer output-SUBWOOFER OUT Setting the low frequency effect attenuator-LFEUsing the Midnight mode DVD S/CVCR S/C Operating procedure Sound adjustmentsBasic adjustment items Press AdjustPress Sound Press Test again to stop the test toneAdjusting the virtual room size for DSP modes Adjusting the bass soundsAttenuating the input signal-INPUT ATT Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsSelecting the FM reception mode To tune in a preset stationIntroducing the Surround modes Creating realistic sound fieldsReproducing theater ambience Dolby Digital3D Headphone mode About other digital signalsDTS All Channel Stereo mode ALL CH Stereo Introducing the DSP modesDigital Acoustic Processor DAP modes About the DSP modes Using the Surround/DSP modesDTSDolby Digital Incoming Signal Type Virtual Surround BackWhen you select Auto Surround Selecting the Surround/DSP modesConnections 2 Video cable connection AV Compu Link remote control systemConnections 1 AV Compu Link connection Not suppliedAutomatic power on/off Connecting procedureAutomatic selection of TV’s input mode One-touch video playOperating other JVC products Changing the remote control code for DVD recorder DVD recorder or DVD playerRelease STANDBY/ON DVR/DVD Release STANDBY/ON TV/DBS/CATV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Manufacturers’ codes for TVTry to operate your VCR by pressing Changing the transmittable signals for operating a VCRRelease STANDBY/ON VCR Manufacturers’ codes for VCRManufacturers’ codes for Catv converter/ DBS tuner Try to operate your DVD player by pressingManufacturers’ codes for DVD player Problem Possible Cause Solution TroubleshootingPower Remote control TunerFM tuner IHF SpecificationsAmplifier AM tunerPage Page Audio Video Control Receiver
Related manuals
Manual 88 pages 24.22 Kb

RX-D205S, RX-D206B specifications

The JVC RX-D205S and RX-D206B are two versatile and feature-rich audio receivers designed to deliver high-quality sound experiences for home entertainment enthusiasts. Both models are part of JVC's commitment to providing advanced audio technologies while ensuring user-friendly functionality and connectivity options.

One of the standout features of the RX-D205S and RX-D206B is their multi-channel surround sound capability. Each receiver supports a range of audio formats, including Dolby Digital and DTS, allowing users to enjoy immersive audio experiences whether they're watching movies, playing video games, or listening to music. With built-in amplification, these models deliver powerful audio performance, making them ideal for both small and large rooms.

Connectivity is a significant highlight for both models. They come equipped with a variety of input options, including multiple HDMI ports, optical and coaxial inputs, and analog inputs. This extensive connectivity ensures compatibility with a wide range of devices such as Blu-ray players, gaming consoles, streaming devices, and more. Additionally, the receivers support 4K Ultra HD passthrough, ensuring that users can enjoy high-resolution video content without compromising on audio quality.

Another key feature is their user-friendly interface and remote control, allowing users to navigate settings, adjust volume levels, and switch between input sources effortlessly. Both models also incorporate Bluetooth technology, enabling wireless streaming from smartphones and tablets. This feature enhances convenience, allowing users to easily enjoy their favorite playlists or podcasts directly from their mobile devices.

In terms of design, the RX-D205S and RX-D206B boast a sleek and modern aesthetic, making them fitting additions to any home entertainment setup. They are designed for durability and longevity, with high-quality components that contribute to their excellent sound performance.

In summary, the JVC RX-D205S and RX-D206B are impressive audio receivers that combine innovative technologies with practical features. Their multi-channel support, versatile connectivity options, Bluetooth capability, and robust design make them excellent choices for anyone seeking to upgrade their home audio system and enjoy an elevated entertainment experience. Whether for casual listening or cinematic immersion, these receivers deliver powerful performance and ease of use, establishing them as noteworthy contenders in the world of home audio.
Top Page Image Contents