ProForm PCTL52580 user manual Maintenance and TROUBLE-SHOOTING, Problem The power does not turn on

Page 12

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-888-963-4266, Monday through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a CUL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Check the batteries in the console. See BATTERY INSTALLATION on page 8. Most problems are the result of drained batteries.

b. Remove the key from the console and

UPLUG THE

POWER CORD.

Remove the screws from the hood.

Locate the Reed Switch (86) and the Magnet (87) on

the left side of the Pulley (85). Turn the Pulley until the

Magnet is aligned with the Reed Switch.

Make sure

that the gap between the Magnet and the Reed

 

Switch is about 1/8”.

If necessary, loosen the Screw

(35)and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

b

 

1/8”

85

86

 

 

87

35

 

Top

 

View

 

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents QUESTIONS? Model No. PCTL52580 Serial NoSerial Number Decal From our factoryTable of Contents Important PrecautionsTreadmill is capable of high speeds Decal shown at the right has been placedBefore YOU Begin For your benefit, read this manual carefully beforeLeft Side Right Side Assembly Do not tighten Handrail Bolt yetMake sure that the Wire Harness is not pinched With the help of a second person, hold the Console BaseThread a Handrail Bolt 15 with a Handrail Washer Tighten all parts used in this step and in steps 2Operation and Adjustment Diagram of the Console Step by Step Console OperationFollow your progress with the four displays Time display Speed display -This disMeasure your pulse, if desired Circulation in your thumb will be restrictedHOW to Fold and Move the Treadmill HOW to Select Kilometres and MilesPower Cord HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USELatch Catch LatchMaintenance and TROUBLE-SHOOTING Problem The power does not turn onProblem The power turns off during use Switch is about 1/8Problem The walking belt slows when walked on Plug the Power CordProblem The walking belt is off-center when walked on Problem The walking belt slips when walked onConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Ordering Replacement Parts Limited WarrantyIcon of CANADA, 900 de l’Industrie, St. Jérôme, QC J7Y 4B8 Remove this Exploded Drawing Part List from the Manual Key No. Qty Description R0800A
Top Page Image Contents