ProForm PFTL99507.0 user manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-perfor- mance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys and your own Phillips screwdriver

and

adjustable wrench

.

 

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included.

1" Tek Screw (2)–4

 

3/8" Star

1/4" Star

3/8" Nut (8)–3

 

Base Pad Spacer

Washer (10)–6

 

Washer (9)–7

 

 

 

(13)–2

 

 

 

1/4" x 1/2"

3/8" x 1 1/4" Bolt (5)–3

3/8" x 2" Bolt (4)–3

Bolt (7)–6

 

 

 

 

3/8" x 4 1/2" Bolt (6)–4

 

1. Make sure that the power cord is unplugged.

1

 

 

38

With the help of a second person, carefully tip

 

 

Hole

the treadmill onto its left side. Partially fold the

 

 

 

Frame (56) so that the treadmill is more stable;

 

83

do not fully fold the Frame yet.

56

81

Cut the tie securing the Upright Wire (38) to the

 

2

Base (83). Locate the tie in the indicated hole in

 

 

Tie

the Base, and use the tie to pull the Upright Wire

 

out of the hole.

 

 

Attach a Base Pad (81) to the Base (83) in the

13

81

location shown with a Base Pad Spacer (13) and

 

a 1" Tek Screw (2). Then, attach another Base

 

2

 

 

Pad (81) with only a 1" Tek Screw (2).

 

 

 

6

 

Image 6
Contents QUESTIONS? Model No. PFTL99507.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedDo not fully fold the Frame yet Careful not to pinch the Upright Wire Gers do not fully tighten the Bolts yetWire Tie Turned on Raise the Frame 56 to the position shown Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeStand on Foot rails Follow your progress with the displayMeasure your heart rate if desired Avoid moving Your handsPress the Start button to start the workout HOW to USE a Personal Trainer WorkoutSelect a personal trainer workout Follow your progress with the display. See onHOW to USE the Ifit Competition Training Center Select the iFIT Competition Training CenterMeasure your heart rate if desired. See on HOW to USE the Settings ModeSelect the settings mode Enter user informationInformation Mode HOW to Adjust the Cushioning SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR1007A Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL99507.0 R1007A Exploded Drawing B-Model No. PFTL99507.0 R1007A Exploded Drawing C-Model No. PFTL99507.0 R1007A Exploded Drawing D-Model No. PFTL99507.0 R1007A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT