ProForm PFTL99707.0 user manual Wire Tie

Page 8

5.With the help of a second person, carefully tip the treadmill onto its right side. Partially fold the Frame (56) so the treadmill is more stable; do not fully fold the Frame yet.

Attach a Base Pad (81) to the Base (83) in the location shown with a Base Pad Spacer (13) and a 1" Tek Screw (2). Then, attach another Base Pad (81) with only a 1" Tek Screw (2).

Remove the 3/8" Nut (8) and the 3/8" x 2" Shoulder Bolt (32) from the Base (83). Attach a Wheel (84) with the Bolt and the Nut that you just removed. Do not overtighten the Nut; the

Wheel must turn freely.

6.With the help of a second person, hold a Bolt Spacer (80) inside the lower end of the Left Upright (74). Insert a 3/8" x 4 1/2" Bolt (6) with a 3/8" Star Washer (9) into the Left Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (80), 3/8" x 4 1/2" Bolt (6), and 3/8" Star Washer (9).

Orient the Left Upright (74) and the Left Upright Spacer (76) as shown. Hold the Left Upright Spacer and the Left Upright against the Base (83). Partially tighten the two 3/8" x 4 1/2" Bolts (6); do not fully tighten the Bolts yet.

Press a Base Endcap (77) into the Base (83).

With the help of a second person, tip the tread- mill so that the Base (83) is flat on the floor.

7.Have a second person hold the Bridge (95) near the Right Upright (78). Remove the wire tie from the Upright Wire (38).

Connect the Upright Wire (38) to the Bridge Wire (52). See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

5

 

 

81

83

 

56

 

 

2

 

32

 

 

 

13

 

 

 

84

 

2

81

 

 

8

6

 

 

 

6

74

 

9

 

 

76

 

 

80

 

77

80

 

83

 

 

 

7

95

 

 

 

 

52

 

 

38

 

 

 

78

Wire Tie

52

38

8

Image 8
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL99707.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Do not fully fold the Frame yet AssemblyMake sure that the power cord is unplugged Not fully tighten the Bolts yet Careful not to pinch the Upright WireWheel must turn freely Wire Tie Be careful not to pinch the wires Bolts and then tighten themRaise the Frame 56 to the position shown Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeFollow your progress with the display Measure your heart rate if desiredStand on Foot rails Avoid moving Your handsHOW to USE a Personal Trainer Workout Select a personal trainer workoutPress the Start button to start the workout Follow your progress with the display. See onHOW to USE the Ifit Competition Training Center Select the iFIT Competition Training CenterHOW to USE the Settings Mode Select the settings modeMeasure your heart rate if desired. See on Enter user informationInformation Mode Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR1107A Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL99707.0 R1107A Exploded Drawing B-Model No. PFTL99707.0 R1107A Exploded Drawing C-Model No. PFTL99707.0 R1107A Exploded Drawing D-Model No. PFTL99707.0 R1107A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty