ProForm PFTL57706.0 user manual Top View Problem The walking belt slows when walked on

Page 20

Locate the Reed Switch (63) and the Magnet (46) on the left side of the Pulley (47). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8". If necessary, loosen the Screw (7), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8"

7

Top

View

63

47

46

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2"–3"

Rear Roller Bolts

c. If the walking belt still slows when walked on, please see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to over- tighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt slips when walked on, first re- move the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clock- wise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

a

b

20

Image 20
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL57706.0 Serial No Table of Contents Important Precautions Page Back Before YOU BeginRight Side Firmly tighten the Extension Leg Bolts AssemblyMake sure that the power cord is unplugged Extension Leg. Firmly tighten the Extension Leg Bolts Bolts but do not tighten them yet. Then, atTreadmill until it is completely assembled See steps 1 and 3. Fully tighten the two Front Endcap Screws PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Turn on the fan if desiredHOW to USE a Calorie Program Press the Start button to start the programHOW to USE the POUND-A-WEEK Program HOW to USE a Cross Training Program Select a cross training programPerform the first strength exercise when Prompted Continue the cross training programInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR0807A Qty DescriptionDescription Model Exploded Drawing B-Model No. PFTL57706.0 R0807A Exploded Drawing C-Model No. PFTL57706.0 R0807A Exploded Drawing D-Model No. PFTL57706.0 R0807A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty