ProForm PFTL49406.1 user manual Assembly, Make sure that the power cord is unplugged, Bolts yet

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own phillips screwdriver

.

Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag, check to see if it has been preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly.

3/4" Tek Screw (72)–2

3/4" Screw (23)–10

1" Tek Screw (77)–6

Cover Screw (52)–4

 

Pulse Bar Star

Endcap Screw

Pulse Bar

Console Screw (67)–4

3/8" Star

Washer (65)–4

(108)–2

Screw (64)–4

 

Washer (83)–4

 

 

 

 

 

2 3/4" Upright Bolt (85)–2

1" Upright Bolt (84)–2

1 1/4" Bolt (63)–4

1. Make sure that the power cord is unplugged.

1

 

 

 

 

 

With the help of a second person, carefully tip

75

Wire

 

 

 

the treadmill onto its left side as shown. Partially

 

 

 

fold the Frame (26) so the treadmill is more sta-

 

75

 

ble. Do not fully fold the treadmill until it is

 

 

 

 

 

completely assembled.

 

 

 

Identify the Right Upright (76), which has a

 

 

 

sticker attached to it. Hold the Right Upright near

76

 

 

the Base (81). Next, locate the long wire inside of

 

 

 

the lower end of the Right Upright (see the inset

 

 

 

drawing). Secure the end of the wire to the end

 

81

 

of the Upright Wire (75). Then, pull the other end

 

85

 

 

of the wire until the end of the Wire Harness is

 

 

 

extending from the upper end of the Right

26

 

 

Upright.

 

 

 

83

84

 

 

 

 

 

Thread a 2 3/4" Upright Bolt (85) and a 1" Upright

 

 

 

Bolt (84) with 3/8" Star Washers (83) into the bot-

 

 

 

tom of the Right Upright (76). Do not tighten the

 

 

 

Bolts yet.

 

 

 

 

6

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents QUESTIONS? Model No. PFTL49406.1 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Right SideBack Assembly Make sure that the power cord is unpluggedBolts yet Bolts yet See steps 2 and 4. Fully tighten the two Endcap Screws Tighten the Bolts yetPinch any wires Connectors properly see the inset drawConnectors are not Connected Pulse Bar Screws Firmly tighten the four 1 1/4 BoltsCover Screws Side ViewView From Above Small Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired On the foot RailsWhenkey. you are finished exercising, remove HOW to USE a Preset Program Select one of the preset programsInsert the key fully into the console HOW to USE a Heart Rate Program Select a heart rate programFollow your progress with the display Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page R0507A Key Qty DescriptionDRAWING-Model Part 2 Part 3 Part 4 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents