ProForm PFTL59707.2 user manual Troubleshooting, Problem The power turns off during use

Page 19

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 11. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the three 3/4" Screws (10) and carefully pivot the Hood (57) off.

a

10

57

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Mon.-Fri a.m.-6 p.m. MST Sat a.m.-4 p.m. MST QUESTIONS?Model No. PFTL59707.2 Serial No Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyDo not fully fold the Frame yet Tighten the Bolts yet Careful not to pinch the Upright WireERLY, the Console MAY be Damaged Nectors are not Connected PropScrews and then tighten them Raise the Frame 53 to the position shown HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired Time display-WhenDistance/Incline dis Calories/PulseSelect a preset workout HOW to USE a Preset WorkoutCustomize your workout if desired Monitor your progress with the matrix and the displays Information Mode HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description R1007AExploded Drawing A-Model No. PFTL59707.2 R1007A Exploded Drawing B-Model No. PFTL59707.2 R1007A Exploded Drawing C-Model No. PFTL59707.2 R1007A Exploded Drawing D-Model No. PFTL59707.2 R1007A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents