ProForm PFTL59707.2 user manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own Phillips screwdriver and

adjustable wrench .

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses shows the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preat- tached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts, do not use power tools for assembly.

3/4" Screw (10)–5

 

 

 

Base Pad Spacer

3/8" Star

5/16" Star

3/8" Nut (8)–2

Washer (9)–4

Washer (7)–4

 

(25)–2

 

 

 

1" Tek Screw (56)–4

 

3/8" x 2" Bolt (4)–2

 

 

5/16" x 1" Bolt (5)–4

3/8" x 4" Bolt (6)–4

 

1. Make sure that the power cord is unplugged.

1

B

 

With the help of a second person, carefully tip

 

 

A

the treadmill onto its left side. Partially fold the

 

 

 

 

 

Frame (53) so that the treadmill is more stable;

 

 

 

do not fully fold the Frame yet.

 

Hole

78

Remove and discard the two indicated bolts (A)

 

80

 

and the shipping bracket (B).

53

 

79

 

 

 

Cut the tie securing the Upright Wire (78) to the

 

 

56

Base (80). Locate the tie in the indicated hole in

 

 

 

 

 

the Base, and use the tie to pull the Upright Wire

 

 

Tie

out of the hole.

 

 

 

Attach a Base Pad (79) to the Base (80) in the

25

 

 

location shown with a Base Pad Spacer (25) and

 

79

 

a 1" Tek Screw (56). Then, attach another Base

 

56

 

Pad (79) with only a 1" Tek Screw (56).

 

 

 

 

6

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL59707.2 Serial No Mon.-Fri a.m.-6 p.m. MST Sat a.m.-4 p.m. MSTTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedDo not fully fold the Frame yet Careful not to pinch the Upright Wire Tighten the Bolts yetNectors are not Connected Prop ERLY, the Console MAY be DamagedScrews and then tighten them Raise the Frame 53 to the position shown Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeCalories/Pulse Time display-WhenDistance/Incline dis Measure your heart rate if desiredHOW to USE a Preset Workout Select a preset workoutCustomize your workout if desired Monitor your progress with the matrix and the displays Information Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR1007A Qty DescriptionExploded Drawing A-Model No. PFTL59707.2 R1007A Exploded Drawing B-Model No. PFTL59707.2 R1007A Exploded Drawing C-Model No. PFTL59707.2 R1007A Exploded Drawing D-Model No. PFTL59707.2 R1007A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents