PART | R1002A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 1 | Motor Belt | 51 | 1 | Front Belly Pan |
2 | 1 | Pulley/Flywheel/Fan | 52 | 1 | Power Supply |
3 | 4 | Motor Nut | 53 | 4 | Cable Tie Clamp |
4* | 1 | Motor/Pulley/ | 54 | 4 | Cable Tie |
|
| Flywheel/Fan | 55 | 1 | Walking Belt |
5 | 1 | Incline Motor Bolt | 56 | 1 | Latch Spacer |
6 | 1 | Small Nut | 57 | 1 | Rear Roller |
7 | 1 | Incline Motor | 58 | 1 | Belly Pan Spacer |
8 | 1 | Stop Bracket | 59 | 2 | Rear Foot |
9* | 1 | Latch Assembly | 60 | 4 | Rear Foot Screw |
10** | 1 | Optional Hand Weight Set | 61 | 1 | Ground Wire |
11 | 1 | Rear Foot Spacer | 62 | 5 | Ground Wire Screw |
12 | 1 | Frame | 63 | 1 | Belly Pan |
13 | 2 | Interface Bracket | 64 | 1 | Rear Endcap |
14 | 1 | Incline Motor Pivot Bolt | 65 | 2 | Rear Roller Adj. Bolt |
15 | 8 | Incline Motor Nut | 66 | 1 | Motor |
16 | 4 | Guide Screw | 67 | 1 | Latch Decal |
17 | 4 | Plastic | 68 | 4 | Platform Screw |
18 | 2 | Hood Bracket (short) | 69 | 2 | Frame Guide Screw |
19 | 1 | Hood Bracket (long) | 70 | 1 | Catch |
20 | 2 | Warning Decal | 71 | 1 | Walking Platform |
21 | 1 | Reed Switch | 72 | 5 | 8” Cable Tie |
22 | 1 | Reed Switch Clip | 73 | 1 | Frame Guide |
23 | 1 | Motor/Controller Wire | 74 | 1 | Motor Tension Bolt |
24 | 1 | Controller | 75 | 2 | Foot Rail Insert |
25 | 1 | Electronics Bracket | 76 | 15 | Small Screw |
26 | 1 | Circuit Breaker | 77 | 1 | Console |
27 | 1 | Power Cord | 78 | 1 | Ground Washer |
28 | 1 | Power Cord Grommet | 79 | 4 | Long Screw |
29 | 1 | On/Off Switch | 80 | 2 | Front Isolator |
30 | 18 | Hood Bracket Screw/Incline | 81 | 4 | Motor Star Washer |
|
| Shield Screw | 82 | 1 | Upright |
31 | 1 | Incline Base | 83 | 2 | Incline Base Pivot Bolt |
32 | 2 | Frame Pivot Bolt | 84 | 1 | Incline Disk |
33 | 2 | Frame Pivot Spacer | 85 | 2 | Handrail Extension |
34 | 1 | Upright Wire Harness | 86 | 2 | Wheel Bolt |
35 | 1 | Front Roller Adj. Bolt | 87 | 1 | Console Base |
36 | 2 | Roller Adj. Washer | 88 | 1 | Motor Tension Washer |
37 | 1 | Motor Tension Nut | 89 | 8 | 3/4” Screw |
38 | 4 | Motor Bolt | 90 | 1 | Key/Clip |
39 | 2 | Cap Screw | 91 | 1 | Incline Motor Plate |
40 | 1 | Left Foot Rail Cap | 92 | 1 | Right Foot Rail Cap |
41 | 2 | Foot Rail | 93 | 1 | Motor Tension Bushing |
42 | 1 | Front Roller/Pulley | 94 | 1 | Motor Hood |
43 | 1 | Magnet | 95 | 2 | Front Wheel |
44 | 2 | Platform Screw (mid) | 96 | 1 | Incline Motor Shield |
45 | 2 | Isolator | 97 | 4 | Thick Base Pad |
46 | 14 | Isolator Screw | 98 | 1 | Incline Sensor Switch |
47 | 15 | Plastic Fastener | 99 | 1 | Upright Grommet |
48 | 1 | Foam Grip (Right) | 100 | 1 | Allen Wrench |
49 | 2 | Belt Guide | 101 | 21 | Screw |
50 | 1 | Book Holder | 102 | 1 | 20” Wire Harness |
22