ProForm 831.298072 user manual Assembly, Your own phillips screwdriver and adjustable wrench

Page 5

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench

and your own phillips screwdriver and adjustable wrench .

1.With the help of a second person, carefully raise the treadmill to the upright position. While a second person tips the treadmill to one side and holds it, insert one of the Extension Legs (103) into the treadmill as shown. Make sure that the Extension Leg is turned so the Warning Decal (20) is on top.

Next, tip the treadmill to the other side and insert the other Extension Leg (not shown) in the same way. Lower the side of the treadmill so that both Extension Legs (103) are resting flat on the floor.

2.Refer to HOW TO LOWER THE TREADMILL FOR USE on page 10. Follow the instructions in step 2 to lower the treadmill.

Attach the latch support to the center hole in the left Upright (82) with a 3/4Ó Screw (81). Make sure that the

Screw is tight, but do not overtighten it; if the Screw is overtightened, the latch will not slide smoothly.

Remove the tape from the Latch Assembly (77). Be careful to hold the parts in place. Inset drawing (a) shows how the Latch Assembly fits together. Refer to inset drawing (b). Insert the springs into the bracket as shown. Make sure the tabs are touching the bracket and the back end of the latch is flush with the bracket.

Attach the Latch Assembly (77) to the left Upright (82) with two 3/4Ó Screws (81).

1

 

 

20

 

 

103

 

 

2

a

 

82

Bracket

 

 

 

81

 

 

77

 

 

81

Latch

 

 

 

Latch

b

Tabs

 

Support

Spring

 

Flush

Spring

3.Slide the upper end of a Handrail (75) onto the right Upright (82) as shown. Note: It will be necessary to pivot the Handrail to the side and back repeatedly (see arrow A) while pushing on the Handrail (see arrow B) to slide it fully onto the Upright. Next, pivot the lower end of the Handrail down, push it toward the right Upright, and then align it with the indicated hole.

Slide the other Handrail (75) onto the left Upright (82) as described above.

3

 

 

B

82

75

 

 

82

75

 

 

A

 

Hole

5

Image 5
Contents SEARS, Roebuck and CO., Hoffman ESTATES, IL Model No Serial NoImportant Precautions Table of ContentsPage Left Side Right Side Before YOU BeginYour own phillips screwdriver and adjustable wrench AssemblyPage Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Battery Installation Console DiagramOn the face of the console, remove it Key STEP-BY-STEP Console OperationReset the speed control Insert the key fully into the power switchAdjust the incline of the treadmill as desired Start the walking beltHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USESymptom the Power does not Turn on TROUBLE-SHOOTINGSymptom the Power Turns OFF During USE TopProblem The walking belt slips when walked on Problem The walking belt slows when walked onProblem The walking belt is off-center when walked on Conditioning Guidelines HOW to Measure Your Heart RateExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description Part LISTÑModel NoExploded DRAWINGÑModel No 103 104 102 107 101 105 108 100 SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantyModel No