PART | R0406A |
To locate the parts listed below, see the EXPLODED DRAWING on pages 21 to 23.
Key |
|
| Key |
|
| Key |
|
|
No. | Qty. | Description | No. | Qty. | Description | No. | Qty. | Description |
1 | 1 | Motor Belt | 42 | 1 | Front Roller/Pulley | 85 | 2 | Latch Screw |
2 | 1 | Pulley/Flywheel/Fan | 43 | 1 | Magnet | 86 | 2 | Wheel Bolt |
3 | 4 | Motor Nut | 44 | 4 | Platform Screw | 87 | 1 | Console Base |
4* | 1 | Motor/Pulley/ | 45 | 2 | Isolator | 88 | 1 | Console Crossbar |
|
| Flywheel/ Fan | 46 | 2 | Center Platform Screw | 89 | 1 | Static Decal |
5 | 1 | Incline Motor Bolt | 47 | 4 | 2 3/4” Bolts | 90 | 1 | Key/Clip |
6 | 1 | Controller Wire | 48 | 1 | Shield | 91 | 1 | Incline Motor Belly Pan |
7 | 1 | Incline Motor | 49 | 2 | Belt Guide | 92 | 2 | Roller Adj. Washer |
8 | 1 | Filter Wire | 50 | 1 | Fan | 93 | 1 | Book Holder |
9 | 1 | Left Upright | 51 | 1 | Front Belly Pan | 94 | 1 | Motor Hood |
10 | 1 | Right Upright | 52 | 1 | Small Nut | 95 | 2 | Front Wheel |
11 | 1 | Console Plate | 53 | 3 | Cable Tie Clamp | 96 | 1 | Incline Motor Shield |
12 | 1 | Frame | 54 | 4 | Cable Tie | 97 | 4 | Base Pad |
13 | 1 | Fan Cover | 55 | 1 | Walking Belt | 98 | 1 | Small Bolt |
14 | 2 | Fan Screw | 56 | 2 | Crossbar Bolt | 99 | 1 | Upright Grommet |
15 | 6 | Wheel Nut/ | 57 | 1 | Rear Roller | 100 | 1 | Allen Wrench |
|
| Incline Motor Nut | 58 | 4 | Hood Screw | 101 | 8 | 3/4” Tek Screw |
16 | 4 | Belt Guide Screw | 59 | 2 | Rear Foot | 102 | 2 | Controller Screw |
17 | 1 | Wire Harness | 60 | 2 | Upright Cap | 103 | 1 | Power Board Plate |
18 | 2 | Hood Bracket | 61 | 1 | Ground Wire | 104 | 4 | Base Cap |
19 | 1 | Front Hood Bracket | 62 | 20 | Screw | 105 | 2 | Incline Pivot Nut |
20 | 2 | Warning Decal | 63 | 1 | Left Rear Endcap | 106 | 1 | Transformer |
21 | 1 | Reed Switch | 64 | 1 | Right Rear Endcap | 107 | 1 | 1/2” Silver Screw |
22 | 1 | Reed Switch Clip | 65 | 2 | Rear Roller Adj. Bolt | 108 | 1 | Photo Switch |
23 | 1 | Left Handrail | 66 | 1 | Drive Motor | 109 | 2 | Hood Plate |
24 | 1 | Controller | 67 | 1 | Latch Decal | 110 | 2 | 1” Spacer |
25 | 1 | Electronics Bracket | 68 | 2 | Foot Rail Cover | 111 | 1 | Hood Spacer |
26 | 1 | Reset/Off | 69 | 3 | Small Star Washer | 112 | 2 | Bumper |
|
| Circuit Breaker | 70 | 1 | Incline Disk | 113 | 1 | Edge Guard |
27 | 1 | Power Cord | 71 | 1 | Walking Platform | 114 | 2 | 1/2” Spacer |
28 | 1 | Power Cord Grommet | 72 | 5 | 8” Cable Tie | 115 | 4 | 1” Tek Screw |
29 | 8 | Washer | 73 | 1 | Incline Bolt | 116 | 2 | Belly Pan Interface |
30* | 1 | Latch Assembly | 74 | 1 | Motor Tension Bolt | # | 1 | 8” Blue Wire, 2F |
31 | 1 | Incline Frame | 75 | 2 | Right Foot Rail | # | 1 | 4” Blue Wire, 2F |
32 | 2 | Frame Pivot Bolt | 76 | 6 | 3/4” Screw | # | 1 | 8” White Wire, 2F |
33 | 2 | Frame Pivot Spacer | 77 | 1 | Latch Bracket | # | 1 | 8” White Wire, Pigtail |
34 | 1 | Tension Bushing | 78 | 1 | Console | # | 1 | 4” White Wire, M/F |
35 | 1 | Front Roller Adj. Bolt | 79 | 1 | Stop Bracket | # | 1 | 8” Green Wire, 2 Ring |
36 | 1 | Foot Rail Cap (Right) | 80 | 2 | Incline Pivot Nut | # | 1 | User's Manual |
37 | 1 | Motor Tension Nut | 81 | 8 | Star Washer |
|
|
|
38 | 4 | Motor Bolt | 82 | 1 | Base | * Includes all parts shown in the box | ||
39 | 10 | Cap Screw | 83 | 2 | Incline Frame Bolt | # These parts are not illustrated | ||
40 | 1 | Foot Rail Cap (Left) | 84 | 2 | Motor Tension |
|
|
|
41 | 1 | Left Foot Rail |
|
| Washer |
|
|
|
20