ProForm user manual Part LIST-Model No. PFEL5105.0, Key Description No. Qty

PART LIST—Model No. PFEL5105.0								R0805A
Key		Description	Key		Description	Key		Description
No. Qty.			No. Qty.			No. Qty.
1	1	Base	42	4	Crank Bushing	84	6	M8 x 23mm Button
2	1	Frame	43	2	Crank Bushing Sleeve	85	1	Screw
3	1	Upright	44	2	Crank Bearing Set			M6 x 10mm Button
4	1	Console Bracket	45	1	Crank	86	2	Screw
5	1	Console	46	1	Crank Spacer			Crank Screw
6	1	Front Stabilizer	47	2	Crank Snap Ring	87	8	Hub Screw
7	1	Rear Stabilizer	48	1	Upper Wire Harness	88	10	M8 Washer
8	1	Left Handlebar	49	1	Lower Wire Harness	89	2	M10 x 60mm Button
9	1	Right Handlebar	50	1	Reed Switch/Wire	90	3	Screw
10	2	Handlebar Endcap	51	1	Belt			M8 Split Washer
11	1	Left Upper Body Arm	52	1	Flywheel	91	1	Flywheel Spacer
12	1	Right Upper Body Arm	53	1	“C” Magnet	92	1	Flywheel Washer
13	1	Left Pedal	54	1	Pillow Block	93	1	Flywheel Snap Ring
14	1	Left Pedal Leg	55	1	Magnet	94	4	Pillow Block Screw
15	1	Right Pedal	56	1	Spring	95	1	Stop Screw
16	1	Right Pedal Leg	57	1	Idler	96	1	M8 x 35mm Screw
17	2	Upright Cover	58	1	Idler Bracket	97	1	“E” Clip
18	1	Left Front Handlebar	59	1	Clamp	98	4	Pulley Screw
19	1	Cover	60	1	Reed Switch Bracket	99	2	Crank Washer
		Left Rear Handlebar	61	1	Base Pin	100	2	M4 x 25mm Screw
20	1	Cover	62	2	Latch Bracket Spacer	101	8	M4 x 16mm Round
		Right Front Handlebar	63	2	Hair Pin	102	4	Head Screw
21	1	Cover	64	1	Latch Bracket			Motor Washer
		Right Rear Handlebar	65	1	Pivot Bracket	103	27	M4 x 16mm Screw
22	1	Cover	66	2	Pivot Bracket Spacer	104	8	M4 x 14mm Screw
		Water Bottle Holder	67	1	Frame Pin	105	6	M4 x 32mm Round
23	2	Front Stabilizer Endcap	68	1	Latch Button	106	2	Head Screw
24	2	Rear Stabilizer Endcap	69	1	Roll Pin			M8 x 31mm Shoulder
25	2	Wheel	70	1	Motor	107	4	Screw
26	1	Base Foot	71	1	Resistance Cable Pulley			M4 x 12mm Screw
27	2	Leveling Foot	72	1	Resistance Cable Set	108	2	M4 x 45mm Screw
28	1	Left Side Shield	73	2	Foam Grip	109	2	Large Wave Washer
29	1	Right Side Shield	74	1	Pivot Axle	110	2	M8 Small Washer
30	6	Upper Body Bushing	75	2	Hub Cover	111	2	Wave Washer
31	4	Pedal Leg Cover	76	2	Outer Crank Cover	112	8	Star Washer
32	2	Pedal Leg Axle	77	4	M6 x 20mm Button	113	1	M10 Washer
33	4	Pedal Leg Bushing	78	4	Screw	114	1	M6 Nut
34	1	Base Axle			M8 x 43mm Button Bolt	115	4	M8 x 23mm Shoulder
35	2	Base Bushing	79	7	M8 Jamnut	116	2	Screw
36	2	Crank Arm	80	1	M8 x 69mm Button Bolt			Flywheel Bracket
37	2	Inner Crank Cover	81	4	M10 Nylon Locknut	#	2	Allen Wrench
38	2	Crank Hub	82	2	M10 x 80mm Carriage	#	1	Grease
39	1	Pulley Spacer	83	2	Bolt	#	1	User’s Manual
40	1	Pulley			M10 x 127mm Button
41	2	Crank Bushing Cover			Screw

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts.

21