ProForm PFEL03010 user manual

Page 7

3.Insert the pulse wires beneath the indicated bracket on the Upright (3) and up out of the hole in the top of the Upright. Attach the T-Handle (10) to the Upright with two M6 x 16mm Screws (54) and two M6 Black Nylon Locknuts (55).

4.While another person holds the Console (6) near the Upright (3), attach the ground wire to the Upright with an M4 x 16mm Screw (34). Connect the Extension Wire (61) to the corresponding console wire. Connect the pulse wires to the corresponding console wires.

Pull any slack Resistance Cable (26) up out of the Upright (3) and push it into the Console (6). Feed the slack Extension Wire (61) down into the Upright. Attach the Console to the Upright with four M4 x 16mm Screws (34). Be careful to avoid pinching the wires or pinching or kinking the Resistance Cable.

Press the Resistance Knob (50) onto the upper end of the Resistance Cable (26).

5.Find the Left Pedal (31), which has a ridge on the right side. Attach the Left Pedal to one of the Pedal Arms (12) with three M4 x 19mm Round Head Screws (16) as shown.

Repeat this step to attach the Right Pedal to the other Pedal Arm (not shown).

6.Locate the Left Handlebar (8) (there is an “L” sticker on the Left Handlebar for identification). Apply a thin film of the included grease to the axle at the lower end of the Left Handlebar.

Slide a Handlebar Spacer (39) and the Pedal Arm

(12)with the Left Pedal (31) onto the Left Handlebar

(8)as shown. Make sure that there are two Pedal Arm Bushings (11) in the Pedal Arm. (Note: These parts fit tightly; it may be helpful to use a rubber mal- let). Next, refer to the PART IDENTIFICATION CHART on page 5 and identify the 3/4” Axle Caps

(43).Tap a 3/4” Axle Cap onto the Left Handlebar.

Repeat this step to attach the other Pedal Arm (12) to the Right Handlebar (62).

7

3

 

 

 

 

Pulse

 

 

Wires

Hole

 

54

Bracket

 

 

 

3

 

10

 

 

 

 

55

4

6

50

 

 

Console

26

 

Wires

 

 

61

 

26

 

 

 

 

Pulse Wires

 

34

Ground

 

 

Wire

34

 

 

 

 

3

5

 

Ridge

 

 

 

 

31

 

 

12

16

 

 

6

 

 

 

 

62

 

8

12

 

 

39

 

11

 

 

43

 

 

 

 

Grease

12

 

 

 

31

 

Image 7
Contents Model No. PFEL03010 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Back Before YOU BeginFront Left SideExtra parts may be included Part Identification ChartAssembly Page Page HOW to Adjust the Resistance of the Pedals HOW to USE the Elliptical TrainerSTEP-BY-STEP Console Operation HOW the Pace Programs OperateStorage MaintenanceConsole TROUBLE-SHOOTING Pulse Sensor TROUBLE-SHOOTINGExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key Qty Description Part LIST-Model No. PFEL03010Exploded DRAWING-Model No. PFEL03010 Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT