ProForm PFTL49101 user manual Assembly, Your own phillips screwdriver Two adjustable wrenches

Page 5

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench

and your own phillips screwdriver

, two adjustable wrenches

wire cut-

ters

, and a rubber mallet

.

 

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

 

 

 

Handrail Bolt (91)–2

 

Extension Leg

 

 

 

 

Screw (53)–2

Handrail Washer (92)–2

 

 

 

 

 

 

Rack Bolt (89)–2

Screw (33)–6

 

 

 

 

 

 

 

Wheel Bolt (36)–2

Handrail Nut (47)–2

Wheel Nut (22)–2

Rack Washer

 

(41)–2

 

1. With the help of a second person, carefully raise the

1

Uprights (11) until the treadmill is in the position shown.

 

 

11

2a.Check to see if the Wheels (37) are attached to the

2a

Extension Legs (34). If the Wheels are attached, go to

 

step 2b. If they are not attached, attach a Wheel to each

36

Extension Leg with a Wheel Bolt (36) and a Wheel Nut

34

(22) as shown. Tighten the Wheel Bolts only until

 

they are snug; do not overtighten them.

 

 

22

 

36

 

37

2b.Insert one of the Extension Legs (34) into the treadmill

2b

as shown. Make sure that the Base Pad (40) is on the

11

indicated side. Note: It may be helpful to tip the Uprights

(11) in the direction shown by the arrow as you insert

 

the Extension Leg. To fully insert the Extension Leg, it

 

may be necessary to tap it with a mallet.

53

 

Attach the Extension Leg (34) with an Extension Leg

 

Screw (53). Note: If there are short and long Extension

 

Leg Screws, use the long Screw. Make sure to push

34

on the head of the Screw while tightening it.

Attach the other Extension Leg (34) in the same way.

40

 

5

Image 5
Contents Customer HOT Line QUESTIONS?Model No. PFTL49101 Serial No Important Precautions Table of ContentsPage Back Before YOU BeginRight Side Your own phillips screwdriver Two adjustable wrenches AssemblyTers A rubber mallet On the head of the Screw while tightening itTwo Screws 33. Be careful not to overtighten Console Base 46. Important Make sure thatPerformant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord STEP-BY-STEP Console Operation Diagram of the ConsoleBattery Installation Reset the console and start the walking belt Insert the key fully into the power switchAdjust the incline of the treadmill as desired CALORIES/FAT CALORIES/PULSEHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to USE the Hand Weights HOW to Lower the Treadmill for USE HOW to Move the TreadmillTop Maintenance and TROUBLE-SHOOTINGProblem The power turns off during use Symptom the Walking Belt is OFF-CENTER Symptom the Walking Belt Slows When Walked onWorkout Guidelines Conditioning GuidelinesExercise Intensity Suggested Stretches Exercise FrequencyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty Remove this Exploded Drawing and Part List from the Manual Qty Description R1200AExploded DRAWING-Model No