ProForm PFSY2925.0 user manual System is tipped over forward see drawing 14b

Page 10

14. Note: This step may be easier if the resistance

14a

 

 

 

 

system is tipped over forward (see drawing

 

 

 

 

 

 

 

 

69

14b).

 

 

 

 

 

 

41 59 38

 

 

 

 

 

Use the wire in the Rear Frame (10) to pull the

 

 

37

 

 

 

 

41

 

 

Long Cable (42) through the Rear Frame and out

 

 

 

 

37

of the Swivel Arm (12). Have a second persons

 

 

 

 

39

 

 

 

 

 

hold the cable end until step 15 is completed.

12

 

 

42

 

 

 

 

 

Hold a 90mm Pulley (38) under the Long Cable

 

 

 

 

 

(42) as shown. Insert an M10 x 132mm Button

 

10

 

 

Bolt (69) into a Finger Guard (37), a Cable Trap

 

 

 

42

 

 

 

 

(39), the Pulley, an M10 Washer (59), an 8mm

 

 

 

 

 

 

 

 

 

Spacer (41), another Finger Guard, and another

 

 

 

 

 

8mm Spacer. Note: The end of the Bolt must

 

 

 

 

 

be flush with the edge of the last spacer. Make

14b

 

 

 

 

sure that the Cable Trap is oriented to hold

 

 

 

 

 

the Cable in the groove of the Pulley.

 

69

10

 

 

See drawing 14b. Insert the 90mm Pulley (38)

 

 

 

 

 

inside the Rear Frame (10). Push the M10 x

 

 

 

 

 

132mm Button Bolt (69) through the Rear Frame

 

 

38

 

 

and the Right Upright (7). Tighten an M10 Nylon

 

 

 

 

 

Locknut (56) onto the Bolt.

 

 

 

 

7

 

 

56

 

 

Tighten the M10 Nylon Locknuts (56) used in

 

 

 

 

 

 

 

 

 

steps 3 and 7.

 

 

 

 

 

15. Make sure that the Long Cable (42) is below

15

 

 

 

 

the rod in the Swivel Arm (12).

 

 

 

56

 

 

 

 

 

 

 

 

 

Attach a 90mm Pulley (38) inside the Swivel Arm

 

 

 

82

 

 

 

 

 

(12), under the Long Cable (42), with an M10 x

 

Rod

 

 

59

51mm Button Bolt (74), two M10 Washers (59),

 

 

 

 

two 5mm Spacers (82), and an M10 Nylon

 

82

 

 

 

Locknut (56).

74

59

12

 

 

 

 

 

 

 

 

 

 

38

 

 

 

 

42

 

 

 

16. Attach the Backrest (30) to the Upright Base (5)

16

 

 

 

 

and the Uprights (6 and 7) with four M6 x 76mm

7

6

60

 

 

64

Screw (64) and four M6 Washers (60).

 

 

 

 

 

 

 

 

 

 

 

 

 

60

64

 

 

 

 

 

 

30

 

 

 

60

 

 

 

 

 

 

 

 

5

 

 

 

10

 

 

 

 

Image 10
Contents Model No. PFSY2925.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Right Side Before YOU BeginLeft Side Assembly Make Things Easier for YourselfPage Page Page Page System is tipped over forward see drawing 14b Hold the cable end until is completedPage Adjusting the Seat AdjustmentsAdjusting the Resistance Attaching the Handles Attaching the Pulley HousingsAttaching the Squat BAR Attaching the LEG Lever Cable DiagramLong Cable Four Basic Types of Workouts Exercise GuidelinesPersonalizing Your Exercise Program Part LIST-Model No. PFSY2925.0 Qty DescriptionPart Identification Chart Exploded Drawing A-Model No. PFSY2925.0 Exploded Drawing B-Model No. PFSY2925.0 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT