Accusplit AH190M28 Sec128-Sec129, Sec130-Sec131, Additional Information, Replacing the Battery

Page 8

Sec1:28-Sec1:29

 

 

ADDITIONAL INFORMATION

5.

Take out the old battery and replace it with a new

 

 

 

 

 

Replacing the Battery

 

battery. Place the battery’s positive (+) terminal FACE

 

 

 

UP while you install it into the pedometer.

 

 

 

 

 

 

 

1.

When the figures on the display start to blink, it is time

6.

CAUTION: Please DO NOTTOUCH inner pedometer

 

 

 

to replace the battery.

 

parts, other than battery.Touching the sensor

 

 

2.

The unit uses oneType CR2032 3-volt lithium battery.

 

mechanism may affect the accuracy of the pedometer.

 

 

3.

Insert a coin into the slot at the bottom of the body

7.

Reinstall the BATTERY HOLDING PLATE by tightening

 

 

 

case.Twist the coin to remove the front case.

 

the two screws. Put the case back together by matching

 

 

4.

Locate the BATTERY HOLDING PLATE at the bottom

 

the top edges of the front case and back case together,

 

 

 

then pressing the bottom of the case together. If the

 

 

 

left corner of the inside case. Remove the plate by

 

 

 

 

 

two halves don’t go together easily, check if the front

 

 

 

loosening the two small screws with a small Phillips

 

 

 

 

 

case is upside down!

 

 

 

head screwdriver.

 

 

 

 

8.

Reset the CLOCK. WEIGHT, and STRIDE to restore all

 

 

 

 

 

 

28

 

 

functions to your pedometer.

 

 

 

 

29

 

 

 

 

 

 

 

 

 

 

 

 

 

Sec1:30-Sec1:31

 

Changing the Unit of Measure

INDEX

 

 

 

 

 

 

 

 

To change between English (feet, pounds) and metric units:

Battery, replacing

. . . .28-29

 

 

 

Clock, setting

. . . . . .5-7

 

 

 

1.

Repeatedly press the yellow MODE button until display

 

 

 

Current day’s results, viewing

.2-3,15-16

 

 

 

 

is in STEP mode.

 

 

 

 

Exiting setup mode

. . . . . . 13

 

 

 

2.

S1: Press yellow S1 (MODE) button for 2 seconds to

 

 

 

Memory

2-3, 18-19

 

 

 

 

enter SET mode.

Memory, resetting

. . . . . . 21

 

 

 

3.

S2: Press yellow S2 (MODE) button repeatedly until

Setting up pedometer

. . . . . 4-13

 

 

 

 

STRIDE setting flashes (there will be a line under “DIST”).

Speedometer

. . . . . . 22

 

 

 

4.

S3: Simultaneously press and hold the yellow S2 (MODE)

Stopwatch

. . . .23-24

 

 

 

Stride Length, setting

. . . . 10-13

 

 

 

 

and S3 ▲ (MEMORY) buttons for at least 5 seconds.The

 

 

 

 

Timer

. . . .25-26

 

 

 

 

unit will shift to the other measurement system.

 

 

 

 

Unit of measure, changing. . .

. . . . . . 30

 

 

 

5.

S4: Press and hold yellow S4 (MODE) button for

 

 

 

Wearing pedometer

. . . . . . 14

 

 

 

 

2 seconds to exit SET mode.

 

 

 

30

Weight, setting

. . . . . . . 8

31

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 8
Contents 7329 Sec11Sec12-Sec13 DisplaysSetting UP Your Pedometer Setting the ClockSec14-Sec15 Sec16-Sec17Setting Your Weight Setting Your Stride LengthSec18-Sec19 Sec110-Sec111Using Your Pedometer Exit Setup ModeSec112-Sec113 Sec114-Sec115Viewing Previous Days’ Results Sec116-Sec117Sec118-Sec119 Sec122-Sec123 Using the Stopwatch and TimerSec120-Sec121 Using the Countdown Timer 01402Sec124-Sec125 Sec126-Sec127Replacing the Battery Sec128-Sec129Sec130-Sec131 Additional Information