Tech4o CW2, CW1 manual Pace Mode, Countdown Timer Mode, Dual Time Mode, Chronograph Mode

[ST/STP]

Increase

hold [ST/STP]

Increase faster

[LAP/RESET]

Decrease hold [LAP/RESET]

Decrease faster

[ST/STP]

Increase

hold [ST/STP]

Increase faster

[LAP/RESET]

Decrease

hold [LAP/RESET]

Decrease faster

CHRONOGRAPH MODE:

This watch is a stopwatch

•Measurement unit: 1/100th second

•Measuring capacity: 99 hours 59 minutes & 59.99 seconds

•The watch will measure elapsed time, lap time and display elapsed time without stopping measurement

NOTE: If NO INPUT for 1 minute during the setup, the display will default to the Countdown Timer Mode

To Use the Timer

• Once a target time has been set (expl. 15 min. ) Press [ ST/STP ] to start

Chronograph Display

•Running time (hour, minute) - displays in the 2nd row

•Running time (second, 1/100th second) - displays in the 3rd row

•Animated (1/100th of a second) - displays in the perimeter bar graph

run time	run time
(hour)	(minute)
run time	1/100 sec
(second)

(digits will descend to zero). Press [ ST/STP ] again to terminate the countdown

(digits will stop)

• Elapsed time will display through out the countdown

To Reload the Timer

• Press (when the timer has stopped) [ LAP/RESET ] to reload the target time

Alarm Sound

To Measure Elapsed Time
• In Zero Display, Press [ ST/STP ] once to	lap time
start measurement - ( the digits will
advance). Press [ ST/STP ] once again to stop
- (digits will not advance) The elapsed time	Lap Display
between the 1st Press [ ST/STP ] and the	[LAP/
2nd Press [ ST/STP ] will display	RESET]

•The watch will beep once when it reaches 5, 4, 3, 2 and 1 seconds

•The watch will sound a long beep at zero.

NOTE: Press [ MODE ] to exit the Countdown Timer

PACE MODE

Pace mode allows users to track their paces

while performing advanced orienteering

To Display Lap Time

•With the chronograph active, Press [ LAP/RESET ] and the cumulative lap times will display

•Press [ LAP/RESET ] again to return to counting display.

NOTE: When the lap time is displayed the elapsed time is still being measured in the background

[ST/STP]

elapsed time (run)

Zero Display Run Display

[ST/STP]

[LAP/RESET]

techniques in the wilderness. Users will match	beats per
their hiking pace with the pacer function’s	minute
audible beeps to maintain and track their speed
and distances over unfamiliar terrain.	Pace Display

• The rate can be set in a range from 40 beats per minute to 180 beats per minute in 5 beat increments

To Reset the Chronograph

•If you wish to record a new set of elapsed times, Press (when the chronograph has stopped) [ LAP/RESET ] to reset the chronograph

elapsed time (stopped)

Stopped Display

Pace Display

• The rate (beats per minute) - displays in the 2nd row

To Use the Pace Feature

• Once a pace rate has been set (expl. 60 BPM), Press [ ST/STP ] to start

hold

[MODE] [MODE]

40 180

COUNTDOWN TIMER MODE

This watch is a countdown timer

•Measurement unit: 1 second

•Measuring capacity: 99 hours 59 minutes & 59 seconds

• The watch will descend from the target time to zero		animated
Countdown Timer Display		bar graph
	running time
• The running time (hour, minute) -		running time
	(hour)
displays in the 2nd row		(minute)
	running time

• The running time (seconds) -	(second)
displays in the 3rd row
	Countdown Timer
• Animated (1 second) - displays in
the perimeter bar graph

the sound. Press [ ST/STP ] again to stop

To set the Pace

• In the Pace Mode, Press and Hold [ MODE ] for 2 seconds until the "beat

rate" digits flash

• Press [ ST/STP ] to raise the value or [ LAP/RESET ] to lower the value. Note: If

you Press and Hold the button, the rate of change is faster

• When the rate is set, Press [ MODE ] to confirm

x 5 BPM

180 40

x 5 BPM

To Set the Countdown Timer Target Time

• In the Countdown Timer Mode,

Press and Hold [ MODE ] for 2

NOTE: If NO INPUT for 1 minute during setup, display will default to Pace Mode

seconds until the "seconds"

digits flash

• Press [ MODE ] to navigate to the

setting that you wish to change.

See navigation chart at right

• When the setting you wish to

change flashes, Press [ ST/STP ]

to raise the value or [ LAP/RESET ]

to lower the value. Note: If you

Press and Hold the button, the

rate of change is faster

• When the hour is set, Press

[ MODE ] to confirm

Countdown Timer Mode

hold [MODE]

second

[MODE]

minute

[MODE]

hour

[MODE]

DUAL TIME MODE

This watch is a dual time piece. Dual time is synchronized with current time

Dual Time Display

•Dual time (hour, minute) - displays in the 2nd row

•Dual time (seconds) - displays in the 3rd row

•Animated (1 second) - displays in the perimeter bar graph

	animated
dual time	bar graph
	dual time
(hour)
dual time	(minute)
(second)
	Dual Time Mode