Seiko S141 Memory Recall Function Single Memory Mode, Memory Recall Function Block Memory Mode

3. SPLIT/LAP TIME MEASUREMENT Lap time

￿Press “D” to show the STOPWATCH 1 (Accumulated elapsed time) display or STOPWATCH 2 (Lap

time in progress) display. Start

A	￿	B	￿	B	￿	A
START	SPLIT/LAP 1		SPLIT/LAP 2			STOP

* The split/lap time can be measured repeatedly by pressing “B.”

Split/lap No.

Accumulated elapsed

time display

Accumulated elapsed time

	B	Split time
￿	RESET	“Split time” refers to an elapsed time required to
		cover a distance from the start to a given point.
		“Lap time” refers to an elapsed time required to
		cover a given section of the whole distance.

Split time

Lap time
Lap time in progress		Lap time in progress
display mark		display
	Lap time in progress

Notes:

1.When the digits are reset to “00” by pressing “B,” a new block number for the next measurement is displayed.

2.In the lap time in progress display, when the lap time measurement in progress exceeds 1 hour, the hour digit appears in place of the mark for lap time in progress display.

MEMORY RECALL FUNCTION ------- SINGLE MEMORY MODE

•Up to 300 lap/split time data of one measurement can be stored in memory and recalled on display.

•With each press of “C,” the stored data is recalled. The data can be recalled successively one after another by keeping “C” pressed.

•The stored data can be recalled even during measurement (while the stopwatch is measuring).

•Memory recall sequence

When the stopwatch is stopped, with each press of “C,” the stored data will be recalled from the first (oldest) to the last (newest) data. When the stopwatch is measuring, with each press of “C,” the stored data will be recalled from the last (newest) to the first (oldest).

￿MEMORY RECALL WHEN THE STOPWATCH IS STOPPED OR RESET

￿With each press of “C,” the data is recalled chronologically (starting from the first/oldest data). Ex.: When the stopwatch is reset to “00” after the measurement

Reset	First lap time	Split & lap times			Stop time
C		Lap/Split	Split time	Lap time
		number

• When a new measurement is commenced, the lap/split time data o b t a i n e d f r o m t h e p r e v i o u s measurement will be automatically deleted.

RECALL mark appears while the stored data is being recalled on display.

The mark shows the memory recall sequence (descending/ascending).

*The data can be recalled successively by keeping “C” pressed.

*To stop the recall of the data when the stopwatch is stopped, press “A”, “B” or “D.” To stop the recall of the data when the stopwatch is reset, press “A” or “D.”

MEMORY RECALL FUNCTION ------- BLOCK MEMORY MODE

The Cal. 141 features a dual memory mode:

Single memory mode ..... The single memory mode is the default-set mode. The lap/split time data of one measurement from start to stop can be stored.

When the stopwatch is reset, and a new measurement is commenced, the lap/split time data of the previous measurement will be automatically deleted.

Block memory mode ...... The block memory mode is an advanced mode designed for professional level use. A sequence of measurement data obtained

from start to stop (or reset) is recorded as a “block.” Up to 100 blocks of data can be stored in memory without deleting the previous data.

<How to change the memory mode>

1.While in the TIME/CALENDAR display, press “B” 8 times until “BLOCK” appears on the display, above which either “ON” or “OFF” is flashing.

2.Press “A” for 1.5 seconds until the memory mode changes with a long beep.

A

Single memory mode

A

Block mark*

Block memory mode

*When the block memory mode is selected, the BLOCK mark appears at the bottom right on the display regardless of the display mode.

Benefits of block memory mode
Easy data management	The block number as well as starting time and date of measurement are automatically recorded and stored.
Handy data storage	Creation of a new block of data will not erase the previous data in memory. While in the single memory mode,
	a new measurement will delete the latest measurement data.

3