JVC GVT0115-008B manual Important for Laser Products

Page 2

Warnings, Cautions and Others

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF IN DOUBT—CONSULT A COMPETENT ELECTRICIAN.

CAUTION— (standby/on) button!

Disconnect the mains plug to shut the power off completely.

The (standby/on) button in any position does not disconnect the mains line.

The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

CAUTION

Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

Do not place any naked flame sources, such as lighted candles, on the apparatus.

When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

IMPORTANT FOR LASER PRODUCTS

1.CLASS 1 LASER PRODUCT

2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3.CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

CAUTION:

Invisible

laser

 

ADVARSEL: Usynlig laser-

 

VARNING:

Osynlig laser-

 

VARO: Avattaessa ja suo-

radiation

when open

and

 

stråling ved åbning,

når

 

strålning

när denna

del

 

jalukitus

ohitettaessa

olet

interlock failed or defeated.

 

sikkerhedsafbrydere er ude

 

är öppnad och spärren är

 

alttiina

näkymättömälle

AVOID DIRECT EXPOSURE

 

af funktion. Undgåudsæt-

 

urkopplad.

Betrakta

ej

 

lasersäteilylle. Älä

katso

TO BEAM.

(e)

 

telse for stråling.

(d)

 

strålen.

 

(s)

 

säteeseen.

(f)

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1 Front:

No obstructions and open spacing.

2 Sides/ Top/ Back:

No obstructions should be placed in the areas shown by the dimensions below.

3 Bottom:

Place on a level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Front View

 

15 cm

 

Side View

 

 

 

 

15 cm

1 cm

1 cm

15 cm

15 cm

 

 

 

 

 

 

 

10 cm

 

15 cm

G-1

Image 2
Contents Instructions Important for Laser Products Above ALL About This Manual PrecautionsIntroduction Contents Front Panel Location of the Buttons and ControlsFront Panel Display Window Front Panel Display WindowRemote Control FM antenna Supplied Accessories Connecting AntennasGetting Started To connect an outdoor FM antennaAM MW antenna Connecting SpeakersRelease the finger from the clamp To connect an outdoor AM MW antennaConnecting Other Equipment To connect audio equipmentCommon Operations Turning On the PowerSetting the Clock Selecting the Sources and Starting PlayReinforcing the Bass Sound Adjusting the VolumeSelecting the Sound Modes To select the sound modes, pressListening to FM and AM MW Broadcasts Tuning in a StationPresetting Stations Tuning in a Preset Station Searching for Programs by PTY Codes PTY Search Receiving FM Stations with RDSChanging the RDS Information Select alternately appear on the display Switching Temporarily to a Program Type of Your ChoicePress PTY/EON until E.O.NET PTY News NewsPress CD 0 or 0 on the unit Playing Back Discs CD/CD-R/CD-RWPlaying Back the Entire Disc-Normal Play Press CD 3/8Load a disc Basic Disc OperationsProgram Play Press Prog programProhibiting Disc Ejection-Tray Lock Playing at Random-Random PlayRepeating Tracks-Repeat Play Playing Back Tapes Playing Back a TapeCheck the recording direction for the tape RecordingRecording on a Tape Press RECPlay the track on the disc you wish to Record Press REC Disc Direct RecordingOne Track Recording Repeat steps 2 and 3 to record other tracksUsing the Timers Using Daily Timer and Recording TimerSetting Press Standby/on to turn Using Sleep TimerPress Timer to complete the timer Press SleepCause TroubleshootingSymptom ActionHandling discs MaintenanceCleaning the unit Handling cassette tapesAdditional Information Description of the PTY codesSpecifications Memo Memo Micro Component System