NAVIGATOR 2.0
S4
S1
S3 | S2 |
CONTROL BUTTONS
S1. Start/stop button
S2. Lap/reset button
S3. Mode button
S4. Light button
DISPLAY MODES:
The watch has six display modes: HOME TIME / FOREIGN TIME (TM2),
COMPASS (COMP), CHRONOGRAPH (CHR), RECALL (RCL), TIMER (TMR) and ALARM (ALM).
To change from one display mode to another, press S3 button once. The mode description will appear for around 2 seconds before the selected mode is activated.
NOTE: In any setting mode, if there is no key manipulation for around
HOME AND FOREIGN TIME DISPLAY: To display FOREIGN TIME mode, press S1 button when HOME TIME mode is displayed. The mode description (TM2) will be displayed. To change back to HOME TIME mode, press S1 button again.
TO SET THE TIME AND CALENDAR:
1.Press S3 button to select HOME TIME / FOREIGN TIME mode.
2.Press and hold S2 button for around 2 seconds. The second digits will blink.
3.Press S1 button to reset the second digits to zero.
4.Press S3 button, the minute digits will blink.
5.Press S1 button to set the minute digits. Holding down the button will speed up the process.
6.Press S3 button, the hour digits will blink.
7.Press S1 button to set the hour digits. Holding down the button will speed up the process.
8.Follow the same pattern to set the hour format, date, month, year, hourly chime option and button beep option.
9.To set the hour format, press S1 button to toggle between
10.To set the hourly chime option, press S1 button to turn it ON or OFF.
11.To set the button beep option, press S1 button to turn in ON or OFF.
12.After finished making all the set- tings, press S2 button to confirm.
NOTE: The day (of the week) is automatically set in accordance with the date. The date can be set within
the range of 1 January 2008 to 31 December 2099.
NOTE: In FOREIGN TIME settings, only the hour digits and minute digits are open to setting. All other settings are synchronized between HOME TIME and FOREIGN TIME mode.
TO USE THE COMPASS:
Press S3 button to select COMPASS mode. The current time will be displayed for around 0.5 second, then the relative compass point and angular bearing will be displayed.
NOTE: This moving pointer represents the direction of North (N).
NOTE: If there is no key manipulation for 20 seconds, the compass sensor will be deactivated for power saving and the watch will display only the current HOME TIME or FOREIGN TIME (depends on your selection in time mode). Press S1 button to
NOTE: If the compass does not seem
to work well, for example: when it displays the wrong compass direction or it displays“DIST”(distort) on the screen, then you have to calibrate the compass. You should also calibrate it after replacing the battery. If your watch has been exposed to strong electromagnetic fields, such as electric lines, magnets or loudspeakers, then you have to calibrate it again. Please also calibrate the compass before using it for the first time and before a long trip.
NOTE: Because of the difference be- tween true North and magnetic North, you have to compensate it by adjusting the compass declination. The declina- tion angle for your local area may be found below:
City | Declination |
| Angle |
|
|
Anchorage | 22 E |
Atlanta | 4 W |
Bombay | 1 W |
Boston | 16 W |
Calgary | 18 E |
Chicago | 3 W |
Denver | 10 E |
Jerusalem | 3 E |
London | 4 W |
Little Rock | 3 E |
Livingston, MT | 14 E |
Munich | 1 E |
New York City | 14 W |
Orlando | 5 W |
Oslo | 2 W |
Paris | 2 W |
Rio De Janeiro | 21 W |
San Francisco | 15 E |
Seattle | 19 E |
Shanghai | 5 W |
Toronto | 11 W |
Vancouver | 20 E |
Washington DC | 10 W |
Waterbury, CT | 14 W |
|
|
ENGLISH
TO SET THE DECLINATION ANGLE: In COMPASS mode,
1. Press and hold S2 button for
around2 seconds to enter into CAL mode.
2.Press S3 button, the declination angle will blink.
3.Press S1 or S3 button to set the declination angle. Holding down the button will speed up the process.
4.After finished making all settings, press S2 button to return to COM- PASS mode.
TO CALIBRATE THE COMPASS: In COMPASS mode,
1. Press and hold S2 button for
around2 seconds to enter into CAL (cali-
bration) mode.
2.Press S1 button, the pointers will begin to rotate clockwise.
3.Rotate the watch horizontally in clockwise direction slowly for at least 2 rotations, taking at least 15 seconds per rotation.
4.Press S1 button or leave the watch idle for 60 seconds to confirm the calibration process, or press S2 button or S3 button to abort the calibration process.
TO USE THE CHRONOGRAPH:
1.Press S3 button to select CHRONO GRAPH mode.
2.The chronograph will then be displayed in its current status – reset, running or stopped.
3.To resume a counting, press S1 button to resume from where it left off.
4.To start a new counting, reset the chronograph to zero first. Press S1 button to stop counting, then press and hold S2 button for around 2 seconds to reset.
For the measurement of elapsed time, In CHRONOGPRAH mode,
1.Press S1 button to start counting.
2.To stop counting, press S1 button. Press S1 button to resume from where it left off.
3.To reset to zero, press S1 button to stop counting and then press and hold S2 button.
For the measurement of split time, In CHRONOGRAPH mode,
1.Press S1 button to start counting.
2.While the chronograph is running, press S2 button once to register a lap. The lap number and lap time of the registered lap will be displayed. The chronograph is still running in the background.
After around 10 seconds, the lap number and split time of the cur rent lap will be displayed.
3.Repeat the last step until all the laps have been registered.
4.To stop counting, press S1 button. Press S1 button to resume from where it left off.
5.To reset to zero, press S1 button to stop counting, then press and hold S2 button for around 2 seconds.
NOTE: The watch can register and record up to a maximum of 30 laps.
NOTE: The chronograph can count up to a maximum of 99 hours, 59 minutes and 59.99 seconds.
NOTE: You can leave the chronograph running while switching over to other operating modes.