TO USE THE RECALL FUNCTION:
1.Press S3 button to select RECALL mode.
2.Press S1 button to scroll through the recorded individual lap time and total elapsed time.
NOTE: The recall function is available only when there is lap record. The message “NO LAPS” will be displayed if there is no lap record.
NOTE: The lap record will be cleared when the chronograph is reset.
TO SET THE TIMER:
1.Press S3 button to select TIMER mode.
2.Press and hold S2 button for around 2 seconds, the timer selec tion will blink.
3.Press S1 button to toggle between timer interval 1 and timer interval 2 to set.
4.Press S3 button, the second digits will blink.
5.Press S1 button to set the second digits. Holding down the button will speed up the process.
6.Press S3 button, the minute digits will blink.
7.Press S1 button to set the minute digits. Holding down the button will speed up the process.
8.Press S3 button, the hour digits will blink.
9.Press S1 button to set the hour digits. Holding down the button will speed up the process.
10.Press S3 button, the
11.Press S1 button to select among CS (Count Stop), CR (Count Repeat) and CCU (Count Up).
12.After finished making all the set- tings, press S2 button to confirm.
NOTE: Illustration of the
a)CS (Count Stop) – the timer will stop when the countdown teaches zero.
b)CR (Count Repeat) – the timer
will repeat the countdown when the countdown reaches zero.
c)CCU (Count Up) – the timer count up to a maximum of 23 hours 59 minutes and 59 seconds when the countdown reaches zero.
NOTE: The timer cannot be activated if the value of timer interval 1 is set as 0:0’00”.
TO USE THE TIMER:
1.Press S3 button to select TIMER mode.
2.The timer will be displayed in its current state – reset, running, or stopped.
3.To resume a counting, press S1 button to resume from where it left off.
4.To start a new counting, reload the timer first.
Press S1 button to stop counting and then press S2 button.
5.After reaching zero in a countdown, a tune will be emitted. To stop the tune, press any button.
NOTE: You can leave the timer running while switching over to other operating modes.
TO SET THE ALARM:
1.Press S3 button to select ALARM mode.
2.Press S2 button to select among alarm entries 1, 2 and 3 to set.
3.Press and hold S2 button for around 2 seconds. The minute digits will blink.
4.Press S1 button to set the minute digits. Holding down the button will speed up the process.
5.Press S3 button, the hour digits will blink.
6.Press S1 button to set the hour digits. Holding down the button will speed up the process.
7.Press S3 button the alarm fre quency will blink.
8.Press S1 button to select among daily (DL Y) and individual day (of the week) only – Sunday (SUN), Monday (MON, Tuesday (TUE), Wednesday (WED), Thursday (THU), Friday (FRI) and Saturday (SAT).
9.After finished the settings, press S2 button to confirm.
NOTE: The alarm will automatically be activated after being set.
NOTE: The alarm will work according to HOME TIME or FOREIGN TIME (de- pends on your selection in time mode).
TO USE THE ALARM:
In ALARM mode,
1.Press S2 button to select among alarm entries 1, 2 and 3 to set.
2.Press S1 button to activate the alarm. The alarm indicator 
will be displayed.
3.Press S1 button again to deactivate the alarm. The message “OFF” will be displayed.
WHEN AN ALARM GOES OFF:
A
TO USE THE BACKLIGHT:
Press S4 button to turn on the back- light for around 3 seconds.
BEZEL-ACTIVATED BACKLIGHT FUNCTION:
1.Press and hold S4 button for around 3 seconds activated or deactivate the
2.When the function is activated, the light bulb icon 
will be displayed. You can then turn on the backlight for around 3 seconds by touching the bezel of the watch.
NOTE: To use the
LOW BATTERY DETECTION:
When the battery of the watch is close to depletion, the battery low indicator 
will be displayed.
ENGLISH
To reduce carbon foot print, these | ||
FS8127 | ||
soy inks on recycled paper. | ||
Freestyle instructions are printed with |
|