JVC RX-730RBK manual Creating Your Own SEA Mode, Adjust the SEA frequency and its level

Page 33

Creating Your Own SEA Mode

On the front panel only:

If you do not want to store your adjustment, but rather want to adjust the SEA temporarily, skip step 3 below.

1. Press SEA ADJUST so that the Control % / Þ/ @/ #buttons work for the SEA adjustment.

SEA	MEMORY
ADJUST	The lamp next to the button lights up.
	The lamp next to the button lights up.

2. Adjust the SEA frequency and its level.

•Press Control @ / #to select the frequency range to adjust.

•Press Control % / Þto adjust the level.

100 1k 10k

3.Press MEMORY (next to the SEA ADJUST button). Your adjustment is stored into USERMODE.

SEA

ADJUST

MEMORY

To recall your own SEA adjustment

See page 27.

To erase a stored adjustment

Front panel

Storing a new adjustment into USERMODE erases the previously stored one.

Page 28

Image 33

Contents RX-730RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-730RBK Table of Contents Before Installation Checking the Supplied AccessoriesGetting Started Switches, Buttons and Controls Front PanelFront Panel How to open the outside panel Remote ControlRemote Control Outside panel Outside panelUsing the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasFM Antenna Connections AM MW/LW Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the subwoofer speaker Connecting the rear and center speakersOpen the terminal Close the terminalCase 2 When you connect front speakers and a center speaker Case 1 When you connect only front speakersCase 3 When you connect front and rear speakers About the speaker impedance of the speakersAudio component connections Connecting Audio/Video ComponentsAudio Components Video Components If your audio components have a Compu LINK-3 terminalVCR Video component connectionsPutting Batteries in the Remote Control Connecting the Power CordPlug the power cord into an AC outlet Press Power to set it in the on positionTurning the Power On and Off Basic OperationsSelecting the Source to Play From the remote control Adjusting the VolumeSelecting the Front Speakers On the front panel onlyFrom the remote control only Listening with HeadphonesMute appears on the display and the volume turns off Muting the SoundAdjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness From the remote control Press Balance L/R -/+Using the Sleep Timer To cancel the Sleep TimerFrom the remote control Press Sleep repeatedly Large Small Selecting the Center Speaker SizeLarge SmallExamples Using Visual ConfirmationTo store the sound settings Press ONE Touch Operation Using the One Touch OperationTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyStoring the preset stations Receiving Radio BroadcastsTuning in a preset station Selecting the FM Reception ModeAuto MonoAssigning Names to Preset Stations Using the RDS Radio Data System to Receive FM Stations What Information Can RDS Signals Provide?PTY Searching for a Program by PTY Codes News AlarmAffairs InfoTA NEWS/INFO TA/INFO TA/NEWS Switching to a Broadcast Program of Your Choice TemporarilyNews Info TA/NEWS/INFO CaseUsing the SEA Modes Selecting Your Favorite SEA ModeRock Musical Movie Country SEA OFF Usermode Jazz Adjust the SEA frequency and its level Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing JVC’s Hall Surround Using the Surround ProcessorWhat is surround? Prologic 3CHLOGIC Hall Surr OFFDelay 1 Delay Delay 4 Delay DelayDelay Press Delay to adjust the delay timeThis case Speaker Arrangements for Dolby SurroundWide Normal Phantom Preparing for Dolby SurroundIf necessary, adjust the speaker output level as follows SOFT2 SOFT1 Flat SHARP1 SHARP2 Press Test again to stop the test tone Press Test to start checking the speaker output balanceUsing Dolby Surround From the remote control Press Menu Using the On-Screen Display to Control the ReceiverPress %/ Þto move To SETTING, then press @ / # Press %/ Þto move to SOURCE, then press @/ #Listening at Low Volume Loudness Also see Press %/ Þ / @ / #to adjust the SEA mode as you want Press %/ Þ to move To SEA Adjust then press @ / #Press %/ Þto move to TUNER, then press @ / # Press %/ Þto move to SEA, then press @ / #Press %/ Þto move To SURROUND, then press @/ # Press %/ Þto move to Surround ADJUST, then press @ / #Press %/ Þto move to one of the surround modes For Dolby 3ch LogicRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingTo operate JVC audio components using this remote control Using the Remote ControlTuner Sound control section AmplifierCD player-changer CD playerCassette deck TurntablePreset Channel + To operate JVC video components using this remote control0, +10 Selects the TV channels Enter button after selecting a channel numberPrograming a series of operations Simplifying the Operations Using the Remote ControlPress Cancel Erasing a programRepeat until you program up to 16 steps Open the outside panel of this remote control Storing the signalsPress one of the buttons on the remote mode section Operating the Other Manufacturers’ Audio/Video ComponentsPress Learn to finish the storing procedure Using stored signalsErasing stored signals Problem Possible Cause Solution TroubleshootingSpecifications AmplifierVideo FM tuner IHF AM MW/LW tunerGeneral EN, GE, FR, NL, SP, IT 0697OFYOTKJEM