JVC RX-558RBK Connecting the Speakers, AM MW/LW Antenna Connections, Basic connecting procedure

Page 7

AM (MW/LW) Antenna Connections

 

 

 

 

Snap the tabs on the loop into the

ANTENNA

 

slots of the base to assemble the

FM 75

AM (MW/LW) loop.

COAXIAL

 

 

 

 

 

Basic connecting procedure

1

2

3

 

 

 

English

AM

LOOP

AM

EXT AM (MW/LW) Loop Antenna

123

Outdoor single vinyl-covered wire

Turn the loop until you have the best reception.

Notes:

•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM (MW/LW) loop antenna connected.)

Connecting the Speakers

You can connect the following speakers:

•Two pairs of front speakers to produce normal stereo sound.

•One pair of rear speakers to enjoy the surround effect.

•One center speaker to produce more effective surround effect (to emphasize human voices).

•One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 11.

For each speaker (except for a subwoofer), connect the (–) and (+) terminals on the rear panel to the (–) and (+) terminals marked on the speakers. For connecting a subwoofer, see page 5.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

1Cut, twist and remove the insulation at the end of each speaker signal cable.

2Open the terminal and then insert the speaker signal cable.

3Close the terminal.

Connecting the front speakers

You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another pair to the FRONT SPEAKERS 2 terminals).

Right speaker

 

FRONT SPEAKERS 1

 

Left speaker

 

 

FRONT SPEAKERS

RIGHTLEFT

1

1

2

2

Right speaker

 

FRONT SPEAKERS 2

 

Left speaker

 

 

4

Page 6 Page 8
Image 7
Page 6 Page 8
Contents RX-558RBK Per I’ltalia Español Italiano Table of Contents To use the Cursor control buttons w on the front panel Remote ControlParts Identification Front PanelGetting Started Before InstallationConnecting the FM and AM MW/LW Antennas Checking the Supplied AccessoriesAM MW/LW Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Other ComponentsConnecting the rear and center speakers Connecting the subwoofer speakerIf your audio components have a Compu LINK-3 terminal Video component connectionsReplace the cover Connecting the Power CordPutting Batteries in the Remote Control Plug the power cord into an AC outletOn the front panel Turning the Power On and Off StandbyFrom the remote control Basic OperationsRecording a Source Adjusting the VolumeMuting the Sound Selecting the Front SpeakersReinforcing the Bass Attenuating the Input SignalAdjusting the Front Speaker Output Balance Adjusting the ToneSetting Center and Rear Speakers for DSP Modes Basic SettingsChanging the Source Name Press ONE Touch Operation Storing the Basic Settings Adjustments One Touch OperationAdjust the sound using the functions listed to the left Using the Sleep TimerUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Appears on the display Selecting the FM Reception ModeUsing the RDS Radio Data System to Receive FM Stations Press FMListening to an FM station To search for a program using the PTY codesSearching for a Program by PTY Codes Press PTY Search whilePress TA/NEWS/INFO until Switching to a Broadcast Program Your Choice TemporarilyPress EON so that the last selected Program type appears on DisplayDolby Surround Using the DSP Modes3D-PHONIC modes Surround ModesRear Available DSP Modes According to the Speaker ArrangementFront Rear SpeakerAdjusting the DAP Modes Adjusting the 3D-PHONIC ModesRear speaker output level Press Rearl / + to adjustPress Test to check the speaker Output balanceActivating the DSP Modes Until the DSP mode you want Appears on the displayTo cancel the DSP mode Press Surround repeatedlyActivating the DVD Multi Playback Mode Using the DVD Multi Playback ModeSynchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Same timeTuner Operating Other ComponentsSound control section Amplifier CD playerTV CH -/+ Cassette deckMD recorder DVD playerProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsAM MW/LW tuner FM tuner IHFGeneral EN, GE, FR, NL, SP, IT 0299HIMMDWJEM
Related manuals
Manual 32 pages 5.36 Kb

RX-558RBK specifications

The JVC RX-558RBK is a versatile and feature-rich audio receiver that caters to home theater enthusiasts and casual listeners alike. This receiver is designed to deliver impressive audio performance while providing a wide range of connectivity options and user-friendly features.

One of the standout characteristics of the JVC RX-558RBK is its power output, which can produce up to 100 watts per channel. This ample power ensures that your audio experiences, whether from movies, music, or gaming, are immersive and filled with vibrant sound. The receiver is equipped with a robust amplifier that offers clear and dynamic audio reproduction across various frequencies.

The RX-558RBK features multiple audio decoding technologies, including Dolby Digital and DTS, which allow for an enhanced surround sound experience. This makes it an excellent choice for creating a stunning home theater setup. The receiver supports various audio formats, providing flexibility for users who enjoy diverse content.

Connectivity options are abundant with the RX-558RBK. It comes with multiple HDMI inputs, allowing users to connect their Blu-ray players, gaming consoles, and streaming devices seamlessly. The HDMI ARC (Audio Return Channel) capability simplifies connectivity by allowing audio signals to be sent back to the receiver from a TV, eliminating the need for additional cables.

Another notable feature of the JVC RX-558RBK is its built-in FM/AM tuner, which enables users to enjoy their favorite radio stations with ease. The receiver includes digital presets for convenient access to preferred channels. Additionally, for those who prefer modern streaming options, the RX-558RBK is compatible with Bluetooth technology, allowing for wireless audio streaming from smartphones, tablets, and other devices.

User convenience is prioritized with the RX-558RBK, featuring an intuitive interface and a well-designed remote control. The on-screen display makes setup and navigation straightforward, minimizing the learning curve for new users.

In terms of build quality, the JVC RX-558RBK boasts a sleek design with a clean aesthetic that complements any home decor. It also incorporates protective circuit designs to ensure longevity and reliability.

In summary, the JVC RX-558RBK is a powerful, feature-packed audio receiver that combines advanced technologies, robust performance, and ease of use. Whether you are looking to enhance your movie watching or elevate your music listening experience, the RX-558RBK stands out as a solid option in the audio receiver market.
Top Page Image Contents