JVC LVT1007-010A[A] Connecting the Speakers, Insert the speaker signal cable, Speaker layout

Page 11

Connecting the Speakers

You can connect the following speakers:

•Two pairs of front speakers to produce normal stereo sound.

•One pair of surround speakers to enjoy the surround effect.

•One surround back speaker or one pair of surround back speakers to enjoy to produce more effective surround effect.

•One center speaker to emphasize human voices.

•One subwoofer to enhance the bass.

CAUTION:

Use only the speakers of the SPEAKER IMPEDANCE indicated by the speaker terminals.

•When connecting to both of the FRONT SPEAKERS 1 and 2 terminals, use speakers with an impedance of 16 Ω to 32 Ω.

•When connecting to either the FRONT SPEAKERS 1 or 2 terminals, use speakers with an impedance of 8 Ω to 16 Ω.

Basic connecting procedure

1 Twist and remove the insulation at the end of each speaker signal cable (not supplied).

2 Open the speaker terminal.

+ –

RIGHT

LEFT

LEFT

RIGHT

 

For FRONT SPEAKERS 2 terminals

3 Insert the speaker signal cable.

Speaker layout

Ideal speaker layout varies depending on the conditions of your listening room. The diagram below is a recommended typical example.

Subwoofer

Left front speaker(s)

Center speaker

Right front speaker(s)

(L)

(C)

(R)

Left surround

Right surround

speaker (LS)

speaker (RS)

Surround back speakers (LSB/RSB)

RIGHT

LEFT

4 Close the speaker terminal.

RIGHT

LEFT

+ –

LEFT

RIGHT

+ –

LEFT

RIGHT

For each speaker (except for a subwoofer), connect the (+) and (–) terminals on the rear panel to the (+) and (–) terminals marked on the speakers.

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents RX-7032VSL RX-7032VSL Table of Contents Introduction FeaturesPrecautions Buttons 15, 44 Remote ControlParts Identification Inside the front door Front PanelDisplay Window Press down on PUSH-OPEN How to open the front doorOutput Rear PanelGetting Started Before InstallationChecking the Supplied Accessories Putting Batteries in the Remote ControlOutdoor FM Antenna Cable Connecting the FM and AM AntennasAM Antenna Connections FM Antenna ConnectionsClose the speaker terminal Connecting the SpeakersInsert the speaker signal cable Basic connecting procedureSurround and surround back speakers Connecting the subwoofer speakerPlacing speakers Front speakers and center speakerCD player Connecting Audio/Video ComponentsAnalog Connections Cassette deckTo listen to the sound after connection, press VCR Video component connectionsIf your video components have an AV Compulink jack TV and/or DBS tunerTo listen to the sound after connection, press DVD Multi DVD playerDVD player Digital output terminal Connecting the Power CordPlug the power cord into an AC outlet Digital ConnectionsBasic Operations Daily Operational Procedure Selecting the Source to PlayTurning On the Power Selecting different sources for picture and sound Adjusting the VolumeSpeaker and signal indicators on the display When analog input is selected Always lights upTo use the speakers connected to the Front Speakers Selecting the Analog or Digital Input ModeListening with headphones only Subwoofer SoundTo select the analog input mode again Setting the Dynamic RangePress TAPE/CDR Turning Analog Direct On and OffPress Analog Direct so that a Direct appears on the display Press TV SOUND/DBSChanging the Display Brightness Using the Sleep TimerReinforcing the Bass Muting the SoundPress FM or AM to select the band Tuning in to Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo tune in a preset station Selecting the FM Reception ModeWhile listening to an FM station, press FM Mode Press the 10 keys to select a preset channel numberPress in Multi JOG Push SET Basic SettingsSetting the Speakers Configuration Remote Press Quick Speaker SetupItems To do See Basic Setting ItemsSpeakers channels number and size Room size and speaker distancePush in Multi JOG Push SET Basic ProcedurePress Setting Setting the SpeakersMeasuring unit-DIST Unit Setting the Speaker DistanceSurround back speakers quantity-SBACK OUT 2SPK Select this to use 2 surround back speakersSelect the playback sounds channel Setting the Bass SoundsSelecting main or sub channel-DUAL Mono Select one of the followingTo recall the volume level Setting the Digital Input TerminalsSetting the Component Video Input Memorizing the Volume Level for Each SourceEx. When adjusting the subwoofer level to Adjusting SoundBasic Setting Items Basic Procedure Press AdjustRepeat steps 2 and 3 to adjust the other center frequency Adjusting the Equalization PatternsAdjusting the Speaker Output Levels Equalization adjustment-DIGITAL EQFor Pro Logic II Music only Select a speaker you want to adjustAdjustable parameters For DAP modesReproducing Theater Ambience Introducing the Surround Modes Using the Surround ModesDTS 96/24 What is Dual Mono?DTS Digital Surround DTS Extended Surround DTS-ES3D Headphone Mode-3D H Phone Incoming Signal TypeEX/ES Setting Available Surround Mode Surround Modes Applicable to the Various SoftwareSelect and play any source other than DVD Multi Press Surround to activate the Surround modeActivating the Surround Modes Introducing the DSP Modes Using the DSP Modes3D Headphone Mode Reproducing the Sound FieldActivating the DSP Modes To cancel the DSP modesAll Channel Stereo mode Multi-channel digital signalsPress DVD Multi so that DVD Multi appears on the display Using the DVD Multi Playback ModeActivating the DVD Multi Playback Mode Multi indicator also lights upAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerConnections 2 Video Cable Connection AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection One-Touch DVD Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off One-Touch Video PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCassette deck CD changer7/P CD recorderCH + Operating Video ComponentsDVD player Try to operate your TV by pressing TV If there are more than one code listed for your brand of TVOperating Other Manufacturers’ Video Equipment Release TVFor Catv converter Release CATV/DBSFor DBS tuner Manufacturer CodesFor VCR If there are more than one code listed for your brandRelease VCR Try to operate your VCR by pressing VCRSamsung Sony Toshiba Yamaha Release AudioFor DVD player Denon Panasonic Philips Pioneer 04, 05Problem Possible Cause Solution TroubleshootingVideo SpecificationsAudio RX-7032VSL AUDIO/VIDEO Control Receiver

LVT1007-010A[A] specifications

The JVC LVT1007-010A[A] is a versatile and high-performing soundbar that has gained attention for its robust features and excellent sound quality. Designed to enhance the home entertainment experience, this soundbar seamlessly integrates with various audio and video devices, making it a suitable choice for both casual viewers and hardcore audiophiles.

One of the standout features of the JVC LVT1007-010A[A] is its impressive audio output. The soundbar boasts a powerful amplification system combined with high-quality drivers that produce clear, rich sound across a wide frequency range. This feature ensures that dialogue in movies is crisp and intelligible while providing deep bass for action sequences and music. The built-in subwoofer further enhances the low-end performance, delivering immersive sound that fills the room.

In terms of connectivity, the LVT1007-010A[A] offers multiple options for seamless integration with other devices. It includes HDMI ARC support, allowing users to connect their TV with a single cable for both audio and control functions. Additionally, the soundbar features optical and AUX inputs, making it compatible with various audio sources, including gaming consoles, Blu-ray players, and streaming devices. Bluetooth connectivity is also a highlight, enabling users to stream music directly from their smartphones or tablets effortlessly.

Another significant characteristic of the JVC LVT1007-010A[A] is its sleek and modern design. The soundbar features a slim profile that can easily fit in front of most TVs without obstructing the screen. Its minimalist aesthetics and high-quality finish make it an attractive addition to any living room setup.

The soundbar also comes equipped with several sound modes and presets, allowing users to customize their listening experience based on content type. Whether watching movies, gaming, or enjoying music, users can switch between modes to optimize sound performance. Furthermore, the remote control provided simplifies operation, enabling users to adjust settings without getting up.

Overall, the JVC LVT1007-010A[A] stands out as a dynamic soundbar that delivers a compelling audio experience. Its combination of powerful sound, diverse connectivity options, and stylish design makes it a worthy investment for those looking to elevate their home entertainment systems. Whether you're a movie buff or a music lover, this soundbar is engineered to meet your audio needs.
Top Page Image Contents