Indesit WD 14 manual Washer-dryer does not drain or spin, Check whether

The washer-dryer does not drain or spin.

Does the selected programme incorporates water draining? Some programmes stop at the end of the wash cycles and draining will have to be selected manually.

Is the “Anti-crease" function -where provided - enabled? This function requires manual selection for draining.

Is the drain pump clogged? To check it, turn off the water supply, unplug the washer- dryer and follow the instructions on page 13, or call for technical assistance.

Always get

assistance from

authorised

technicians and always insist on original spare parts.

Is the drain hose kinked? The tract of the drain hose must be as straight as possible. Make sure the drain hose is not squashed or kinked.

Is the washer-dryer’s drain duct clogged? Is there an extension of the drain hose? If so, is it positioned incorrectly, blocking the water flow?

Excessive vibration during the spin cycle.

Have all transit screws been removed durind instal- lation? See the following page on installation procedures.

Has the washer-dryer been levelled correctly? The levelling of the appliance

should be checked periodically. Adjust the feet and check them with a level.

Is there space between the machine and adjacent units? If it is not a built-in model, the washer-dryer will oscillate a bit during the spin cycle. A few cm of space should therefore be left around it.

The washer-dryer leaks.

Is the metal ring of the inlet hose properly attached? Turn off the water supply, unplug the appliance and try tightening its attachment without forcing it.

Is the detergent dispenser obstructed? Remove and wash it under tap water.

Is the drain hose well attached? Turn off the water supply, unplug the appliance and try tightening its attachment.

Too much foam.

Is the detergent appropriate for machine washing? Check whether the definition on its label reads “for machine wash” or “hand and machine wash”, or any other similar wording.

Is the correct amount being used? An excessive amount of detergent, besides producing too much foam, does not guarantee a more effective wash, and causes scaling in the internal parts of the appliance.

The washer-dryer does not dry.

Check whether:

the plug has been correctly inserted into the socket; there is electricity in your home; the appliance door has been shut properly; a delayed start (if available) has not been selected; programme knob A has been set to position (Stop/Reset); the drying cycle knob C has been set to position 0.

Technical characteristics

Model	WD 14
Dimensions	width 59,5 cm
	height 85 cm
	depth 53,5 cm
Capacity	from 1 to 5 kg for the wash programme; from 1 to 2,5 kg for the drying programme
Electrical	voltage 230/240 Volt 50 Hz
connections	maximum absorbed power 2050 W
Water connections	maximum pressure 1 MPa (10 bar)
	minimum pressure 0,05 MPa (0,5 bar)
	drum capacity 46 litre
Spinning speed	up to 1400 rpm
Control programs	wash: programme 3, temperature 60°C. Carried out with 5 kg load;
in compliance with	drying: run with a load of 2.5 kg and knob C set to position	.
IEC regulation 456

This appliance conforms with the following E.E.C. directives:

-73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications

-89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications

The washer-dryer doesn't dry properly.

Check whether:

the end of the drain hose is underwater; the drain pump is obstructed; the advice given on the maximum loads has been taken; the water tap has been turned on.

If, despite all checks, the washer- dryer fails to function and the problem persists, call your nearest authorised Customer Service Centre, providing the following information:

-the nature of malfunction

-the model type no. (Mod. ....)

-the serial number (S/N ....) This information can be found on the data plate situated at the back of the washer-dryer.

Instructions for installation and use 10