Indesit WD 14 Levelling, Connection to the water mains, Electric connection, Replacing the fuse

Page 12

Installation and removal

When the new washer-dryer arrives

Whether new or just transported to a new house, installation is extremely important for the correct functioning of your washer-dryer.

After removing the appliance from its packaging, check that it is intact. If in doubt, contact a qualified technician immediately.

The inside of the machine is supported, for transportation, by four screws on the back panel.

Before using the washer-dryer,remove the screws, remove the spacers together with the rubber tubes attached to them (keeping all the parts) and use the plastic plugs provided to fill in the holes.

Important: Use the cap (provided) to close the 3 holes which housed the stop pin, situated in the right- hand part of the lower back of the washer-dryer.

Levelling

The washer-dryer must be levelled appropriatey in order to guarantee its correct functioning.To level the appliance, the front feet must be adjusted; the angle of inclination, measured according to the worktop, must not exceed 2°. When placed on carpet, make sure the ventilation is not reduced.

Connection to the water mains

Both hot and cold water supplies are preferable and they should be between 34.5kN/m²(5lb/in²) and 1034.2kN/m² (150lb/in²) pressure. The hose having the red end fitting should be encountered between the hot supply and the threaded connection adjacent to the letter H on the rear of the machine. The hose having the white end fittings should be connected between the cold supply and the threaded connection adjacent to the letter C on the rear of the machine. Remember to insert a sealing washer at each connection to ensure watertight joints. Do not overtighten the connections by using tools -hand tight is sufficient topreventleaks.Itisgenerallymore convenient to have these supplies away from the sink taps. Where no suitable hot water supply is available or it does not meet these requirements, both inlet hoses may be connected to a cold supply by using two taps etc., or a « T» junction on the plumbing however, use of cold water only will increase programme times.

Note: the maximum temperature should not exceed 70°C (158°F).

Connecting the drain hose The drain hose (hooked pipe) is secured to the rear of the machine by support clips and may be routed to right or left as required.

The hook to be used in case the drain hose ends at a height below 60 cm.

The drain hose should be placed in a stand pipe with a minimum internal diameter of 38 mm (1½ inches) or it can be positioned over a sink or it can be connected as shown in Fig. A. The height of stand pipe or sink should be between 60 and 100 cm (24 and 40 inches). Care must be taken that the hose is not obstructed, twisted, submerged or kinked. If the hose is connected with an airtight joining, provision should be made to prevent syphoning.

Electric connection

Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIEDELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

The front feet are adjustable.

Retain the transit screws,

spacers and washers. Should you move house then these should be replaced to support the inside of the machine to prevent damage when transporting the machine.

The rubber gasket.

Connect the inlet hose to the threaded connector on the machine rear.

Water pipe inlet at the top right.

The guide for draining into tubs and sinks.

Fig. A

Warning!

The company denies all

liability if and when these norms are not respected.

Plastic bags, expanded

styrofoam, nails and other packaging parts are not children’s toys, and are potentially dangerous.

11Instructions for installation and use

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Washer-dryer Quick guide Never use pipes that have already been usedWhat goes in your washer-dryer? At the end of the wash cycleTemperature control knob Drying cycle knobDetergent dispenser Anti-creaseProgramme for all seasons Cotton programme and a level of dryness Extra dry Now set the wash cycle knobAt the end of the drying cycle Bleaching Ironing Dry cleaning Drying Understanding labelsWatch the weight Never use your washerHow much does it weigh? Holidays unplug the applianceUseful tips about the detergent dispenser Do YOU Need to PRE-WASH? For heavily soiled laundry onlyThis is why you cannot see the water through the door Environment yet without renouncing maximum cleanlinessSimple with the new Indesit technology, you need less than Half of it, to get good results on twice as muchWasher-dryer does not drain or spin Check whetherLevelling Connection to the water mainsElectric connection Replacing the fuseReplacement fuse covers How to connect an alternati- ve plugRemoving the plug EarthWater inlet hose Never exaggerate with dosesYour safety and that Stay in touch Instructions for installation and use Instructions for installation and use Instructions for installation and use Leader for young Europe

WD 14 specifications

The Indesit WD 14 is a versatile and efficient washer-dryer combo designed to meet the needs of modern households. It combines the functionality of both washing and drying in a single appliance, making it a practical choice for individuals and families with limited space.

One of the standout features of the Indesit WD 14 is its generous capacity. With a washing capacity of up to 7 kg and a drying capacity of 5 kg, it can handle large laundry loads, allowing users to wash and dry more items in one go. This is particularly beneficial for busy households where time-saving solutions are essential.

The machine is equipped with a variety of washing programs tailored to suit different fabric types and soil levels. This includes specialized programs for cottons, synthetics, delicate fabrics, and even a quick wash option that delivers clean clothes in under 30 minutes. This flexibility enables users to select the most appropriate cycle for their laundry, ensuring optimal results while preserving garment integrity.

In terms of technology, the Indesit WD 14 features a user-friendly control panel that simplifies operation. It includes a digital display that provides clear information on the selected program, remaining time, and any additional settings. This intuitive design enhances the overall user experience and makes it easy to customize washing and drying preferences.

Energy efficiency is another highlight of the Indesit WD 14. It boasts a respectable energy rating, which helps to reduce electricity consumption and lower utility bills. The machine's innovative sensor drying technology prevents over-drying by automatically detecting moisture levels in the laundry, ensuring that clothes are dried to perfection while conserving energy.

Moreover, the Indesit WD 14 is designed with convenience in mind. Its compact dimensions make it suitable for smaller living spaces, such as apartments or laundry rooms with limited space. The appliance runs quietly, enhancing the user experience even in close quarters.

In conclusion, the Indesit WD 14 washer-dryer combination offers a reliable, efficient, and versatile solution for those looking to streamline their laundry processes. With its notable capacity, various washing programs, user-friendly interface, and energy-efficient features, it stands out as an ideal choice for modern households seeking convenience without compromising on performance.
Top Page Image Contents