4 Installation
Installation and electrical connections of the |
| Appropriate installation location | ||||||||
machine must be carried out by an |
| • Place the machine on a rigid floor that has | ||||||||
Authorized |
| Service | Agent. | Review |
| sufficient load carrying capacity. | ||||
information in the user manual and ensure |
| • Choose a well ventilated dry location out | ||||||||
that the electricity, water supply and water |
| of direct sunlight. | ||||||||
drainage systems are appropriate before |
| • Do not place the machine on the power | ||||||||
calling an Authorized Service Agent. If they |
| cable. | ||||||||
are not, call a qualified technician and |
| • Do not install the machine at places where | ||||||||
plumber | to | have | any | necessary |
| the temperature may fall below 0ºC. | ||||
arrangements carried out. |
|
|
|
| • Place the machine at least 10 mm away | |||||
|
|
|
|
|
|
|
|
| from the edges of other furniture. | |
| Preparation of location, electrical, tap |
| • Hot and cold water taps should be located | |||||||
| water and waste water installations of |
| within 1 metre of the inlet valves. | |||||||
| the machine are the customer's |
| Adjust the adjustable leg of the machine if | |||||||
| responsibility. |
|
|
|
| necessary to ensure that the machine is | ||||
| Warning: | Installation | and | electrical |
| level. The maximum permissible inclination | ||||
| connections of the | machine must be |
| of the ground surface is 2 degrees. A | ||||||
| carried out by an Authorized Service |
| machine that is not levelled and is unstable | |||||||
| Agent. The Manufacturer shall not be |
| will vibrate and generate excessive noise. | |||||||
| held liable for damages that may arise. |
|
|
| ||||||
|
|
|
|
| ||||||
| Warning: Prior to installation, visually |
|
|
| ||||||
| check if the machine has any defects |
|
|
| ||||||
| on it. If so, do not have it installed. A |
|
|
| ||||||
| damaged machine is a safety risk. |
|
|
| ||||||
|
|
|
|
| ||||||
| Ensure that the water inlet, discharge |
|
|
| ||||||
| hoses and | power cable are not folded, |
|
|
| |||||
| pinched or crushed, during or after |
|
|
| ||||||
| installation or cleaning procedures. |
|
| Warning: Do not place the machine | ||||||
|
|
|
|
|
|
|
|
|
| |
Installing the bottom cover |
|
|
|
| on a rug or carpeted floor as this may | |||||
|
|
|
| restrict ventilation openings at the | ||||||
1. Unplug the power cord of the machine. |
|
| bottom of the machine. | |||||||
2. Carefully lay the front side of the machine |
|
|
| |||||||
|
| Warning: Do not use old or used water | ||||||||
on a soft mat or cushion. (Be careful not |
|
| ||||||||
|
| inlet hoses on the new machine It may | ||||||||
to dent the frame) |
|
|
|
|
| |||||
|
|
|
|
| cause stains on your laundry. | |||||
3. Slide the bottom cover into the retainers |
|
| ||||||||
and push the cover all the way in. |
|
| Connecting the water supply | |||||||
4. Fasten the bottom cover with the supplied |
| |||||||||
screw. |
|
|
|
|
|
|
| 1. Check that the sealing washers are | ||
5. Carefully move the machine back into the |
| correctly seated. | ||||||||
upright position. |
|
|
|
|
| 2. Attach the curved end of the water supply | ||||
hose to the inlet valve of the machine, tighten the coupling nuts by hand. Never use a tool when tightening the nuts.
3. Attach the straight end of the hose to the tap. Tighten the coupling nuts by hand.
4. Open the taps fully after completing the hose connection and check for water leaks. If there are any leaks, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.
PAGE 7