Controls Programmes knob, Display, Door Opening

Start and Programmes

The Controls

●Programmes knob

!Warning, if after pressing the START/PAUSE button the programme knob position has changed, the new position will NOT change the programme selected.

To change a selected programme, press the

START/PAUSE button , the light flashes Amber to indicate the programme is paused. Select the new

programme and any options required, the light will then

flash green. Press the START/PAUSE button again and the new programme will start.

●OPTION buttons / lights

These buttons are used to customise the selected programme to your requirements. A programme must have been selected on the programme knob before an option can be selected. Not all options are available for all programmes (see Start and Programmes). If an option is not available and you press the button, the buzzer will beep three times. If the option is available the option light in the button lights to confirm the selection.

After the START/PAUSE button has been pressed only the Sound option (where available) can be changed.

Progress ( Drying, Cool Tumble) icons

These are part of the Display, they indicate the progress of the dryer. Each icon comes on as the corresponding phase starts.

Time Delay (Delay Timer)

The start of some programmes (see Start and Programmes) can be delayed for up to 24 hours. Ensure the water container is emptied before setting a delayed start. During this period the clothes are tumbled to help prevent creases developing.

Extra Care

This Anti-Ageing function for Cottons helps to maintain the brightness of your laundry for a long time, thanks to the correct drum rotation (reduced in the last part of the cycle) and the correct temperature.

Note: It cannot be used with the ‘Extra Dry’, ‘Cupboard Dry’ and ‘Light Dry’ dryness levels.

Heat Level buttons and lights

Not all programmes allow you to change the heat level and some programmes allow all three heat level options: Low, Medium and High.

When the heat level options are available pressing this button changes the heat level and the light corresponding to the selection is lit.

Sound

If selected, gives a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Not available with the Heat & Enjoy programme.

●DISPLAY 8:88

The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme (see The Display).

The colons between the hours and minutes in the display flash to show that the time is counting down.

When the programme finishes its cool tumble phase the display will show ‘End’.

●Empty Water Icon / Container

(If you have plumbed your dryer to a drain this icon can be ignored, as there is no need to empty the water container).

When this icon is on ( ) it reminds you to empty the water container.

If the water container fills during a programme, the heater turns off and the dryer does a period of Cool Tumble then the buzzer sounds, the ‘water container

full’ icon flashes, the display shows and the

‘empty water’ icon is on.

You must empty the water container and restart the dryer or the clothes will not dry. After re-starting the dryer the display will take a few seconds to refresh. To avoid this always empty the water container each time you use the dryer (see Maintenance).

●Door Opening

Opening the door (or pressing the Start/Pause button) during a programme will stop the dryer and have the following effects:

●The START/PAUSE light flashes Amber.

●During a delay phase the delay will continue to count down. The START/PAUSE button must be pressed to resume the delay programme.

●The START/PAUSE button must be pressed to resume programme. The progress lights will change to show the current status and the Start/Pause light will stop flashing and turn green.

●Changing the programmes knob will select a new programme and the START/PAUSE light will flash

green. You can use this to select the Refresh programme to cool the clothes, if you find them dry enough. Press the START/PAUSE button to

begin a new programme.

●Note

If you have a power cut, switch off the power or remove the plug. When power is restored, press and hold the ON/OFF button until the dryer reactivates, then press the Start/Pause button.

Information	Important

Installation

Description

The Display

Programmes	Start and

Laundry

Suggestions	Warnings and

and Care	Maintenance

Troubleshooting
Service