Troubleshooting

If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical

Assistance Centre (see Assistance).		EN
Problem:	Possible causes / Solutions:
The dryer does not start.	•	The plug has not been inserted far enough into the socket to make contact.
	•	There has been a power cut.
	•	The fuse has blown. Try connecting another appliance to the same socket.
	•	If an extension cord is used, try connecting the dryer plug directly into the socket.
	•	The door has not been closed properly.
	•	The programme has not been set correctly (see How to carry out a drying cycle).
	• The START/PAUSE button has not been pressed (see How to carry out a drying cycle).

The drying cycle does not start.

•A delayed start time has been set (see Programmes and options).

•The START/PAUSE button has been pressed; a short delay follows before the dryer starts running. Wait for the drying cycle to start; do not press the START/PAUSE button otherwise the dryer switches to the pause mode and the drying cycle will not start.

Drying times are too long.

The “Empty water container” in- dicator light flashes, but the dryer has been running for a short time.

The “Empty water container” indicator light is on but the water container is not full.

The programme is finished but the items are damper than expected.

•The filter has not been cleaned (see Maintenance).

•The water container must be emptied? The “Empty water container” indicator light flashes and the message appears “H2O” (see Maintenance).

•The condenser needs to be cleaned (see Maintenance).

•The heat setting is not suited to the type of fabric to be dried (see Programmes and options).

•An incorrect drying time was selected for the type of load (see Laundry).

•The items are too wet (see Laundry).

•The air intake grille are clogged up (see “Installation” and “Care and Maintenance”).

•The dryer is overloaded (see Laundry).

•The water container was probably not emptied before starting the programme. Do not wait for the signal for emptying the water container, but always check and empty it before starting a new drying programme (see Description of the tumble dryer).

•It is normal: the “Empty water container” indicator light flashes when the water container is full. If the indicator light is on but is not flashing, it is just a reminder to empty the container (see Description of the tumble dryer).

!For safety reasons, the dryer programmes last a maximum of 5 hours. If an automatic programme has not detected the final dampness level required in this interval, the dryer completes the programme and stops. Check the above points and repeat the programme; if the items are still damp, contact the Technical Assistance Centre (see Assistance).

The code “F” appears on the di- splay followed by one or two num- bers, the options indicator lights and the pause indicator light flash.

“dOn” briefly appears on the di- splay every 6 seconds.

The “Remaining time” indicator changes during the drying cycle.

The dryer is noisy during the first few minutes of operation.

The lights on the dryer control panel are off although the dryer is switched on.

•If the display shows a fault, switch the appliance off and unplug it, then clean the filter and the Heat Pump Filter unit (see Maintenance). Reinsert the plug, switch the appliance on and start another programme. If the display still visualises a fault, contact the Technical Assistance Centre (see Assistance). If the display still visualises other numbers, mark the code and contact the Technical Assistance Centre (see Assistance).

•The appliance is in “Demo” mode. Press the ON/OFF and START/PAUSE buttons and keep them pressed for 3 seconds. The display visualises “dOn” for 3 seconds, then the dryer starts functioning normally.

•The remaining time is constantly monitored during the drying cycle and is updated to show the best forecast. It is normal for the displayed time to increase during the cycle.

•This is normal, especially if the dryer has not been used for a long time. If the noise persists during the entire cycle, contact the Technical Assistance Centre.

•The dryer has gone into standby mode to save power. This occurs if you have left the dryer on or have had a power cut. It occurs after 30 minutes:

-if you leave the dryer without starting a programme;

-after your drying programme has finished.

Press the On/Off button and the lights will come on again.

IDCE 8450 BS H, IDCE 8450 B H, IDCE 8450 BK H specifications

The Indesit IDCE 8450 BK H, IDCE 8450 B H, and IDCE 8450 BS H are part of Indesit’s range of high-efficiency tumble dryers, designed to cater to the needs of modern households. These models are distinguished not only by their stylish appearances—available in black, white, and stainless steel—but also by their intelligent features aimed at enhancing user experience.

One of the standout characteristics of these models is their impressive drying capacity. With a generous 8 kg drum, they can handle large loads of laundry, making them ideal for families or individuals with busy lifestyles. This capacity is complemented by a range of drying programs, allowing users to select the most appropriate setting for different fabric types. Whether you’re drying cottons, synthetics, or delicates, these models provide tailored options to ensure optimal results.

Technology is at the forefront of the Indesit IDCE 8450 series. These models incorporate advanced sensor drying technology, which automatically adjusts drying time based on the moisture level in the clothes. This not only protects garments from damage due to over-drying but also enhances energy efficiency. Users can save on energy bills while taking care of their clothes.

Furthermore, the Indesit IDCE 8450 BK H, B H, and BS H have a variety of smart features. The timer delay function allows users to set the dryer to start at their convenience, offering flexibility for those who want their laundry done while they are out. Also, the reverse action drum helps reduce tangling, making it easier to unload clothes and minimizing creases.

In terms of usability, these dryers come equipped with a clear display and easy-to-navigate controls. Cleaning the dryer is also hassle-free with removable filters that ensure maintenance is straightforward and quick.

Overall, the Indesit IDCE 8450 BK H, IDCE 8450 B H, and IDCE 8450 BS H combine functionality, efficiency, and stylish design, making them perfect choices for users looking to simplify their laundry routine while ensuring the best care for their garments. With a focus on technology and user-friendly features, these models represent the best of modern laundry solutions, catering to the diverse needs of today's consumers.