Indesit IDCE 845 S instruction manual Troubleshooting, Problem Possible causes / Solutions

Page 15

Troubleshooting

If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical

 

Assistance Centre (see Assistance).

 

EN

 

 

 

 

 

Problem:

Possible causes / Solutions:

The dryer does not start.

•The plug has not been inserted far enough into the socket to make contact.

•There has been a power cut.

•The fuse has burned out. Try connecting another appliance to the same socket.

•If an extension cord is used, try connecting the dryer plug directly into the socket.

•The door has not been closed properly.

•The programme has not been set correctly (see How to carry out a drying cycle).

•The START/PAUSE button has not been pressed (see How to carry out a drying cycle).

The drying cycle does not start.

•A delayed start time has been set (see Programmes and options).

•The START/PAUSE button has been pressed; a short delay follows before the dryer starts running. Wait for the drying cycle to start; do not press the START/ PAUSE button otherwise the dryer switches to the pause mode and the drying cycle will not start.

Drying times are too long.

The “Empty water container” indicator light flashes, but the dryer has been running for a short time.

The “Empty water container” indicator light is on but the water container is not full.

The programme is finished but the items are damper than expected.

The code “F” appears on the display followed by one or two numbers, the options indicator lights and the pause indicator light flash.

“dOn” briefly appears on the display every 6 seconds.

The “Remaining time” indicator changes during the drying cycle.

The dryer is noisy during the first few minutes of operation.

•The filter has not been cleaned (see Maintenance).

•The water container must be emptied? The “Empty water container” indicator light flashes and the message appears “H2O” (see Maintenance).

•The condenser needs to be cleaned (see Maintenance).

•The heat setting is not suited to the type of fabric to be dried (see Programmes and options).

•An incorrect drying time was selected for the type of load (see Laundry).

•The items are too wet (see Laundry).

•The air intake grille are clogged up (see “Installation” and “Care and Maintenance”).

•The dryer is overloaded (see Laundry).

•The water container was probably not emptied before starting the programme. Do not wait for the signal for emptying the water container, but always check and empty it before starting a new drying programme (see Description of the tumble dryer).

•It is normal: the “Empty water container” indicator light flashes when the water container is full. If the indicator light is on but is not flashing, it only signals that the water container must be emptied (see Description of the tumble dryer).

!For safety reasons, the dryer programmes last a maximum of 4 hours. If an automatic programme has not detected the final dampness level required in this interval, the dryer completes the programme and stops. Check the above points and repeat the programme; if the items are still damp, contact the Technical Assistance Centre (see Assistance).

•If the display visualises F10 or F15, switch the appliance off and unplug it, then clean the filter and the condenser (see Maintenance). Reinsert the plug, switch the appliance on and start another programme. If the display still visualises F10 or F15, contact the Technical Assistance Centre (see Assistance). If the display still visualises other numbers, mark the code and contact the Technical Assistance Centre (see Assistance).

•The appliance is in “Demo” mode. Press the ON/OFF and START/PAUSE buttons and keep them pressed for 3 seconds. The display visualises “dOn” for 3 seconds, then the dryer starts functioning normally.

•The remaining time is constantly monitored during the drying cycle and is updated to show the best forecast. It is normal for the displayed time to increase during the cycle.

•This is normal, especially if the dryer has not been used for a long time. If the noise persists during the entire cycle, contact the Technical Assistance Centre.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Tumble Dryer Filling of the Water Container Important informationPage Preliminary information InstallationWhere to install the tumble dryer Electrical connections VentilationFeatures Description of the tumble dryerControl panel Page Starting and selecting a programme How to carry out a drying cycleDuration of the wash cycles can be monitored on the display Programme chartProgrammes and options Special/Sport/Partial ProgrammesPage Opening the door OptionsLaundry Sorting laundryCare labels Drying times Special garmentsSaving energy and respecting the environment General safetySuggestions Information on recycling and disposalCare and maintenance Troubleshooting Problem Possible causes / SolutionsAssistance Centre see Assistance Before calling the Technical Assistance Centre AssistanceSpare parts Comparative programmesGuarantee Months Parts and Labour GuaranteeReplacement of any removable parts made of glass or plastic After Sales Service Essential Contact InformationRecycling & Disposal Information Page 195075237.00

IDCE 845, IDCE 845 S specifications

The Indesit IDCE 845 S is a reliable and efficient condenser tumble dryer designed to meet the demands of modern households. This appliance combines ease of use with advanced technology, making it a popular choice among consumers looking for a perfect blend of functionality and performance.

One of the standout features of the IDCE 845 S is its large 8 kg capacity. This enables users to dry a substantial amount of laundry in a single load, which is ideal for families or individuals with busy lifestyles. The dryer is equipped with multiple drying programs, including cotton, synthetic, and delicate settings, providing optimal care for a variety of fabrics. This versatility ensures that users can easily find the right cycle for their specific laundry needs.

Energy efficiency is a significant consideration for many appliance buyers, and the Indesit IDCE 845 S does not disappoint. With an energy rating of B, it offers a balance between effective drying performance and lower energy consumption. This helps in reducing utility bills while also being environmentally friendly.

The technology employed in the IDCE 845 S includes a sensor drying system that automatically adjusts the drying time based on the moisture level detected in the laundry. This feature helps prevent over-drying, preserving the quality of clothes and linens while ensuring optimal energy usage. The ease of use is further enhanced by the intuitive control panel, which includes straightforward settings and an easy-to-read LED display.

Another notable characteristic of this tumble dryer is its compact design, making it suitable for placement in smaller spaces without compromising on performance. The machine is also equipped with a large, easy-to-empty water tank, allowing for hassle-free maintenance and operation.

Noise levels are another essential aspect for many users, and the Indesit IDCE 845 S operates relatively quietly, making it a suitable option for homes where noise can be a concern. Additionally, the appliance is designed with safety features such as overheat protection, providing peace of mind during operation.

In summary, the Indesit IDCE 845 S is a robust and feature-rich condenser tumble dryer that efficiently tackles laundry drying needs. With its spacious capacity, advanced drying technologies, energy efficiency, and user-friendly design, it proves to be a valuable addition to any household. Whether for a busy family or an individual, this model offers convenience and performance that can make laundry days a breeze.
Top Page Image Contents