Hotpoint HV8D 393 First wash cycle, Technical data, Correspond with the coloured markings iden

Page 4

GB

 

As the colours of the wires in the lead may not

 

correspond with the coloured markings iden-

 

 

 

 

tifying the terminals in your plug, proceed as

 

 

follows:

 

 

 

 

 

Connect Green & Yellow wire to terminal

 

 

marked E or

or coloured Green or Green &

 

 

Yellow.

 

 

 

 

 

Connect Brown wire to terminal marked L or

 

 

coloured Red.

 

 

 

 

 

Connect Blue wire to terminal marked N or

 

 

coloured Black.

 

 

 

If a 13 amp plug (BS 1363) is used it must be

 

 

fitted with a

 

 

 

 

 

13 amp fuse, either in the plug or adaptor or

 

 

at the distribution board.

 

 

 

If you are in any doubt regarding the electrical

 

 

supply to your machine, consult a qualified

 

 

electrician before use.

 

 

 

How to connect an alternative plug:

 

 

The wires in this mains lead are coloured in

 

 

accordance with the following code:

 

 

BLUE

 

 

NEUTRAL (N)

 

 

BROWN

 

 

LIVE (L)

 

 

GREEN & YELLOW

EARTH (E)

 

 

 

 

 

 

 

 

GREEN &

 

 

 

 

 

YELLOW

 

 

 

 

 

BROWN

13 ampere fuse

 

 

 

 

 

 

 

 

 

BLUE

CROSS-BAR

 

 

 

 

 

CORD GRIP

 

 

 

 

 

 

 

 

Disposing of the appliance:

When disposing of the appliance please re- move the plug by cutting the mains cable as close as possible to the plug body and dispo- se of it as described on the previous page.

!The washing machine should not be installed in an outdoor environment, not even where the area is sheltered, because it may be very dangerous to leave it exposed to damp, rain and thunderstorms.

!When the washing machine is installed, the mains socket must be within easy reach.

!Do not use extensions or multiple sockets.

!The power supply cable must never be bent or dangerously compressed.

!The power supply cable must only be repla- ced by an authorised serviceman.

Warning! The company denies all liability if and when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 60°C programme.

Technical data

Model

HV8D 393

 

 

 

 

 

width 59.5 cm

 

Dimensions

height 85 cm

 

 

depth 60 cm

 

Capacity

from 1 to 8 kg

 

 

 

Electrical

please refer to the technical

data plate fixed to the ma-

connections

chine

 

 

maximum pressure

Water con-

1 MPa (10 bar)

 

minimum pressure

nections

0.05 MPa (0.5 bar)

 

 

drum capacity 62 litres

Spin speed

up to 1300 rotations per

minute

 

 

 

Test wash

 

 

cycles in

Programme

(60°C);

accordan-

ce with

Cotton Standard 60°.

directives

Programme

(40°C);

1061/2010

Cotton Standard 40°

and

 

 

1015/201

 

 

This appliance conforms to the following EC Directives: - 2004/108/EC (Electroma- gnetic Compatibility)

-2006/95/EC (Low Voltage)

-2012/19/EU

4

Image 4
Contents Instructions for use Washing MachineUnpacking and levelling InstallationElectric and water connections Replacing the fuse Technical data First wash cycleCorrespond with the coloured markings iden Tifying the terminals in your plug, proceed asPage Care and maintenance Precautions and tips General safetyThis appliance can be used by children aged DisposalControl panel Description of the washing machineDetergent dispenser drawer Display Switch the Machine ON. Press the On/Off Modifying the cycle settingsRunning a wash cycle ButtonWash cycles and functions Table of wash cyclesWash functions Super WashDetergents and laundry Detergent dispenser drawerPreparing the laundry Special wash cyclesTroubleshooting Problem Possible causes / SolutionsMachine is noisy Machine wont spin properlyGuaranteeGB Assistance195110444.01 You must register your appliance with us