Hotpoint HV8D 393 manual Troubleshooting, Problem Possible causes / Solutions

Page 13

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

 

GB

that the problem cannot be solved easily using the following list.

 

Problem:

Possible causes / Solutions:

 

 

The machine does not switch on.

The wash cycle does not start.

The appliance is not plugged into the socket fully, or not enough to make contact.

There is no power to the socket, or the fuse has blown in the mains plug.

The door is not closed properly.

The ON/OFF button has not been pressed.

The START/PAUSE button has not been pressed.

The water tap has not been turned on to allow water to flow into the machine.

A delayed start has been set (see “Running a wash cycle”).

The machine does not fill with wa- ter or “NO WATER CHECK SUPPLY” appears on the display.

The water inlet hose is kinked.

The water inlet hose is not connected to the water supply.

The water pressure is too low.

The water tap has not been turned on to allow water to flow into the machine.

There is no water supply to the house.

The inlet valve filter is blocked.

The START/PAUSE button has not been pressed.

The machine continuously fills with water and continually drains away or Water left in the drum

or Stuck on wash.

The top of the drain hose is too low - It must be fitted at a height between 65 and 100 cm from the floor (see “Installation”).

The drain hose is connected incorrectly to the sink trap allowing water to run into the machine, the drain hose must be positioned higher than the bottom of the sink to prevent water flowing down the drain hose.

The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

The machine does not drain or spin or F05 error code in the display.

The Pump filter is blocked.

The drain hose is kinked (see “Installation”).

New Installation - The blanking cap or spigot has not been removed if con- nected under a sink.

The drain hose or sink trap is blocked.

The wash cycle does not include draining, some wash cycles require the drain phase to be started manually.

The REDUCED CREASES function button has been activated. To complete the wash cycle, press the START/PAUSE button (see “Wash cycles and functions”).

The machine does not heat or poor wash results.

The programme takes too long

or The Display changes the estima- ted ‘Time to End’ during the pro- gramme.

The machine vibrates a lot during the spin cycle.

The ‘Spin Speed’ selector knob is in the “OFF” position.

The ‘Temperature’ selector knob is in the “OFF” position.

Programme times will vary due to water pressure, the incoming water tempera- ture and if the wash load goes out of balance. This will increase the programme times accordingly (see ‘ The machine wont spin properly’ below).

The feet have not been adjusted, enabling the machine to rock.

New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

The machine is trapped between cabinets and/or walls.

The load is in a slight out of balance condition and machine is spinning, but at a lower speed.

13

Image 13
Contents Washing Machine Instructions for useUnpacking and levelling InstallationElectric and water connections Replacing the fuse First wash cycle Technical dataCorrespond with the coloured markings iden Tifying the terminals in your plug, proceed asPage Care and maintenance General safety Precautions and tipsThis appliance can be used by children aged DisposalControl panel Description of the washing machineDetergent dispenser drawer Display Modifying the cycle settings Switch the Machine ON. Press the On/OffRunning a wash cycle ButtonTable of wash cycles Wash cycles and functionsWash functions Super WashDetergent dispenser drawer Detergents and laundryPreparing the laundry Special wash cyclesProblem Possible causes / Solutions TroubleshootingMachine wont spin properly Machine is noisyAssistance GuaranteeGBYou must register your appliance with us 195110444.01