Whirlpool 8535841 Plan the exhaust vent installation, Determine vent length, Preferred

Page 8

Plan the exhaust vent installation

Typical installations exhaust from the rear of the dryer.

straight back

offset

Route the vent

The exhaust outlet is located at the center of the rear of the dryer.

The exhaust vent can be routed up, down, left, right or straight out the back of the dryer. See “Recessed area/closet installation” section, Page 4, for space requirements.

This dryer may be converted to exhaust

out the right or left side or through the bottom.

Typical installations for left or right side

exhausting.

Typical installations for bottom exhausting.

To convert the dryer, the following kits are available from your dealer.

Exhaust Kit No. 279818 (white)

Exhaust Kit No. 279819 (almond)

Exhaust Kit No. 279925 (biscuit)

Exhaust Kit No. 279969 (silver)

exhaust air flow

acceptable

better

Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns. Avoid making 90° turns.

When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking.

Determine vent length

Preferred —

 

 

4"

 

 

 

 

 

 

 

 

 

 

4"

 

 

 

 

 

 

 

 

 

 

 

When you have a 4' hood

 

 

 

 

 

 

 

 

Maximum length of 4" diameter

 

 

 

metal vent

Number of

Rigid

 

 

Flexible

90° elbows

 

 

 

 

(fully extended)

0

64 feet

 

 

36 feet

1

54 feet

 

 

31 feet

2

44 feet

 

 

27 feet

3

35 feet

 

 

25 feet

4

27 feet

 

 

23 feet

 

 

 

 

 

 

 

 

Acceptable —

 

 

 

 

 

 

 

 

 

2-1/2"

 

 

 

 

 

 

 

 

 

 

When you have a 2-1/2' hood

 

 

 

 

Maximum length of 4" diameter

 

 

 

metal vent

 

 

 

 

 

 

 

 

Number of

Rigid

 

 

 

 

 

Flexible

90° elbows

 

 

 

 

 

 

(fully extended)

0

58 feet

 

 

 

 

 

 

28 feet

1

48 feet

 

 

 

 

 

 

23 feet

2

38 feet

 

 

 

 

 

 

19 feet

3

29 feet

 

 

 

 

 

 

17 feet

4

21 feet

 

 

 

 

 

 

15 feet

The maximum length of the exhaust

system depends upon:

the type of vent (rigid or flexible metal).

the number of elbows used.

side or bottom exhaust. Side or bottom exhaust adds a 90° turn inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart.

1.See the exhaust vent length chart that matches your type hood for the maximum vent lengths you can use.

Do not use vent runs longer than specified in exhaust vent length charts.

Exhaust systems longer than specified will:

accumulate lint creating a potential fire hazard.

shorten the life of the dryer.

reduce performance, resulting in longer drying times and increased energy usage.

2.Determine the number of elbows you will need.

3.In the column listing the type of metal vent you are using (rigid or flexible), find the maximum length of metal vent on the same line as the number of elbows.

4.Determine the number of 4-inch diameter vent clamps required.

The maximum length using a 2" x 6" rectangular vent with 2 elbows and a 2-1/2" exhaust hood is 8 feet.

For exhaust systems not covered by exhaust vent length charts (such

as multiple unit hookups, plenums, and power-assist fans), see Service Manual, Part No. 603197. (To purchase the Service Manual, see your Use and Care Guide for a toll-free telephone number.)

8

Image 8
Contents Installation Instructions Set to operate on Natural GASYour safety and the safety of others are very important For proper drying performanceIt is your responsibility to CSA InternationalParts needed for installation Closet/confined area Exhaust dimensionsInstallation Power supply cord Ground prong Electrical RequirementsGas supply Recommended ground methodSupply line requirements Natural GasBurner input requirements Dryer must be exhausted outside Mobile home installation requirementsDryer must be fastened to the floor Plan the exhaust vent installation Determine vent lengthPreferred AcceptableInstallation steps Install vent systemIf installing washer and dryer, install dryer first Prepare the dryerTo dryer Position Rigid gas Supply line Make gas connection E. Exhaust dryerClamp Moving dryer to a new location? Snap-Lock fittingsWhirlpool Corporation Benton Harbor, Michigan 49022, U.S.A Lea y conserve estas instrucciones Para funcionar con GAS NaturalPara el debido funcionamiento de la secadora Es su responsabilidadCampana exterior de salida de aire Las instalaciones en casas móviles o rodantes requierenConexión opcional a la secadora GasConfinada No se debe instalar ningún otroVista de FrenteSuministro de gas Método recomendado de puesta a tierraGas natural Gas licuado Propano líquido/L.PRequisitos de entrada del quemador Requisitos de la línea de suministroRequisitos del Sistema de salida De aire Requisitos de instalación en una casa móvil o rodanteExterior de salida de La secadora debe fijarse al pisoDetermine la longitud del conducto La longitud máxima del sistema de salida de aire depende dePreferido AceptableEtapas de la Instalación Instale el sistema de salida de airePrepare la secadora Nivelación de la secadoraAbrazadera de 10,2 cm 4 pulg Conexión del gasSalida de aire de la secadora ¿Va a trasladar de lugar la secadora? Impreso en los EE.UU

8535841 specifications

The Whirlpool 8535841 is a high-quality replacement refrigerator water filter designed to provide clean and fresh drinking water, ensuring that your household stays hydrated with safe water. This filter is compatible with various Whirlpool refrigerator models, making it a versatile choice for those looking to enhance their refrigerator's water filtration system.

One of the standout features of the Whirlpool 8535841 is its advanced filtration technology. This filter uses activated carbon to effectively reduce contaminants such as chlorine, lead, sediment, and other impurities that can affect the taste and smell of your drinking water. With its ability to significantly improve water quality, the Whirlpool 8535841 ensures that every glass of water is crisp and refreshing.

The filter has a long-lasting performance with a lifespan of up to six months or 200 gallons of water, depending on usage and water quality. This durability means less frequent replacements, which not only saves money but also reduces waste. Installing the filter is a straightforward process, ensuring that homeowners can quickly and easily replace their old filters without the need for professional assistance.

Another noteworthy characteristic of the Whirlpool 8535841 is its ability to maintain optimal water flow. Unlike some lower-quality filters that may restrict water pressure, this filter is designed to provide an uninterrupted supply of clean water. This efficient performance is crucial for families that rely on their refrigerator for ice and chilled water, ensuring that there is always plenty of clean drinking water available.

Moreover, the Whirlpool 8535841 is NSF-certified, meaning it meets strict safety and performance standards. Consumers can have peace of mind knowing that this water filter has undergone rigorous testing to confirm its efficacy in reducing harmful contaminants. The certification serves as a testament to the high quality and reliability of the product, making it a trusted choice for many households.

In summary, the Whirlpool 8535841 water filter offers advanced filtration technology, ease of installation, long-lasting performance, and reliable water flow. With NSF certification to back its effectiveness, this filter is an excellent investment for anyone looking to improve their drinking water quality while enjoying the convenience of a refrigerator-based filtration system. Whether for health concerns or the simple desire for better-tasting water, the Whirlpool 8535841 stands out as a top choice in refrigerator water filtration solutions.