Whirlpool 3397617 Electrical requirements, Power supply cord, Use a new 30-amp power supply cord

Page 3

Tools and materials needed for installation:

l duct tape

l/4” socket wrench or nut driver (shown)

1” socket wrench

safety glasses

Parts supplied for installation:

Remove parts from packages. Check that all parts were included.

4 leveling legs

literature package

Electrical requirements

Electrical Shock Hazard

Electrical ground is required on this appliance.

Do Not modify the power supply cord plug. If it does not fit the outlet, have a proper outlet installed by a qualified electrician.

Do Not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in an electrical shock.

Do Not use an extension cord with this appliance.

Check with a qualified electrician to be sure this appliance is properly grounded.

Do Not connect plug end of power supply cord into a live receptacle before connecting power supply cord to dryer terminal block.

Do Not reuse old power supply cord.

Failure to follow these instructions could result in death or serious injury.

If codes permit and a separate grounding wire is used, it is

recommended that a qualified electrician determine that the grounding path is adequate.

A three-wire or four-wire, single phase 120/240-volt, 60-Hz, AC-only, electrical supply (or three-wire or four-wire 120/208-volt if specified on serial/rating plate) is required on a separate

30-ampere circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended.

wirina w

A wiring diagram

the console or on back panel of dryer.

It is the personal responsibility and obligation of the customer to contact a qualified electrician to assure that the electrical installation is adequate

and is in conformance with the National Electrical Code, ANSVNFPA 70 - latest* and all local codes and ordinances.

Copies

of the

standards

listed above may

be obtained

from:

 

*National

Fire

Protection

Association

Batterymarch

Park

 

Quincy,

Massachusetts

02269

Important: Observe all governing codes and ordinances.

Power supply cord

Use a new 30-amp power supply cord.

Local codes may permit the use of a U.L.-listed, 120/240-volt minimum,

30-ampere, dryer power supply cord kit (pigtail). Power supply cord should be Type SRD or SRDT and be at least four feet (1.2 m) long. The wires that connect to the dryer must end with ring terminals or spade terminals with upturned ends. A 3/4”, U.L.-listed strain relief must be installed where the power supply cord connects to the dryer (see Figures 1 and 2).

upturned ends

 

 

 

 

 

rina

 

to this

conductor.

 

terSinals

 

 

 

 

314”

U.L.-listed

/

 

NEUTRAL

 

strain

relief

 

(white or center)

 

Three-wire power supply cord

 

NEMA

lo-30P

 

 

 

 

Figure

1

 

 

314”

U.L.-listed

 

NEUTRAL

strain relief

 

 

\

 

(white),

 

 

 

 

 

 

 

 

 

 

 

 

NEUTRAL

 

 

 

 

 

grounding prong

(green)

ring

\

F

 

 

 

terminals

Four-wire power supply cord (Mobile home or

other four-wire installations) NEMA 14-30P

Figure 2

Page 3

Image 3
Contents Page Dryer door clearances Before you startImportant Observe all governing codes and ordinances Four-inch metal exhaust duct is requiredFour-wire power supply cord Mobile home or Power supply cordUse a new 30-amp power supply cord Three-wire power supply cordElectrical connection Direct wireDirect wire preparation Strain relief firmly to strain relief Attach U.1Relief Hole TightenExhaust requirements Mobile home installation Now startWith dryer in laundry area Electrical Connect Exhaust Duct toDryer See Straightest PathRecessedand closet installation in!structions Minimum installation spacingCloset installation must be exhausted Benton Harbor, Michigan 49022 01995 Page Espacio de la puerta de la Secadora Importante Cumpla todos 10s reglamentos y normas vigentesP6gina Piezas suministradas para la instalacihCable de alimentacih electrica Cable de alimentacibn de 3 hilosCon Aprobaci6n Don Marca El orificio Con&ones elfictricasCable direct0 PClginaFiaura Preparacih del cable Direct0 FiguraPreparacih del cable dire& Figura Los Retlre el tornillo central del bloqueAbajo Izquierda Recta Desde Parte PosteriorCon la secadora en la zona de lavanderia Instalacibn en casas rodantesP6aina Enchufe Cable de Aire Paginas Utilice La via MasEmplee un compuesto de calafatear Exterior alrededor de la campanaInstmcciones de knstalac36n empotrada y en un closet Espacio de instalacibn minim0La instalacion en un closet debe realizarse con una salida Pieza Benton Harbor, Michigan 49022 Sf la secadora no funcionaNecesita Asistencfa Cuando mueva Ia secadora

3397617 specifications

The Whirlpool 3397617 is a highly regarded dryer heating element known for its efficiency and reliability in enhancing laundry performance. This essential appliance component is specifically designed for various models of Whirlpool dryers, ensuring optimal drying capabilities for a wide range of fabrics and loads.

One of the standout features of the Whirlpool 3397617 is its durable construction. Made from high-quality materials, this heating element is built to withstand the rigors of regular use and deliver consistent performance over time. Its robust design minimizes the risk of burns or malfunctions, thereby providing peace of mind to users.

In terms of specifications, the Whirlpool 3397617 operates at a voltage of 240 volts and a wattage of 5,000 watts. This powerful heating element swiftly generates heat, allowing clothes to dry efficiently without prolonged exposure to heat, which can potentially damage delicate fabrics. The rapid heating ability also contributes to shorter drying cycles, making it a practical choice for households with busy schedules.

Another important characteristic of the Whirlpool 3397617 is its compatibility with a variety of Whirlpool dryer models. This versatility makes it an ideal replacement part, as it can easily be substituted in many different units. This compatibility ensures that users can continue to enjoy the reliability and functionality of their dryers without needing to invest in a whole new appliance.

Incorporating advanced coil technology, the Whirlpool 3397617 provides uniform heat distribution throughout the dryer. This feature significantly enhances drying efficiency, ensuring that every piece of clothing is treated evenly, thereby preventing the risk of over-drying or under-drying.

Installing the Whirlpool 3397617 is straightforward, and most users can complete the replacement with basic tools and minimal time. With its combination of quality, performance, and user-friendliness, this heating element stands out as a top choice for anyone looking to maintain their dryer’s effectiveness and prolong its lifespan.

Overall, the Whirlpool 3397617 is emblematic of Whirlpool’s commitment to producing high-quality home appliances. This heating element not only meets but often exceeds consumer expectations, making it an essential component for efficient laundry care.