Using Attachments, Cleaning and Maintenance

Using Attachments

NOTE: When installing or changing attachments, be sure the unit is off, unplugged, and no steam is being released to avoid contact with hot water.

1.Fabric Brush

Helps open the fabric for greater steam penetration.

-Attach the fabric brush onto the steam nozzle (Fig. 3).

-Move the fabric brush in a downward motion from top to bottom gently brushing the fabric.

2.Crease Clamp

Helps create a straight crease

-Attach the crease clamp to the steam nozzle (Fig. 5).

-Push the trigger to open the crease clamp.

-Place the garment between the crease clamp and steam nozzle.

-Release the trigger.

-Move the crease clamp in a downward motion from top to bottom to set a crease.

Cleaning and Maintenance

1.Be sure the steamer is turned off and unplugged.

2.Allow the steamer to cool for at least 30 minutes.

3.Empty any excess water from the water tank and allow it to air dry before replacing the cap and setting it back in the unit.

4.Empty excess water from the reservoir by tipping unit over a sink.

Storing

1.Open the 3 clips (Fig. 2) on the telescopic pole and glide it slowly to collapse being careful not to pinch your fingers. When it is all the way down close the 3 clips back into place.

2.Coil the hose and place on the hanger attachment (Fig. 9)

3. Store in a cool, dry place.

Figure 9

Removing Mineral Buildup

One common problem with steamers is mineral buildup caused by the high mineral content in many municipal water supplies. Mineral residue inside of the internal pipes and heater can cause intermittent steaming or in severe cases no steaming at all.

The best way to avoid this is to use de-mineralized or distilled water in the unit. The procedure below can be used to clear mineral buildup. If you are unable to use de-mineralized or distilled water we recommend you use this procedure every 30 hours of operation to help avoid mineral buildup.

1.Turn the unit off and unplug the power cord.

2.Unscrew and remove the hose from the hose connector on the top of the unit.

3.Remove the pole from the unit.

4.Remove the water tank from the main unit and drain any water in the unit over a sink.

5.Make a mixture of 4 oz. white vinegar and 4 oz. water. In most cases 1 cup of this mixture will be sufficient.

6.Slowly pour the water-vinegar mixture into the hose connector (Fig. 11).

a.If the internal piping is only partially blocked by mineral buildup, the water-vinegar mixture will soon start flowing out of the water intake hole. If this happens proceed to step 8.

b.If the internal piping is completely blocked, continue to pour the mixture into the hose connector until full.

7.Pour the water-vinegar mixture into the water intake hole until full.

8.Let stand for 40 minutes.

9.Drain the water-vinegar mixture from hose connector or the reservoir by tipping the unit over a

10. sink.

Pour clean water through the hose connector and water intake hole until the vinegar smell

11. dissipates.

12. Drain the residual water from hose connector or the reservoir by tipping the unit over a sink. Reassemble the unit and operate normally.

If the procedure above does not return the unit to normal operation, the unit may need servicing.

Water Intake

Hose Hole

Connector

Figure 11

PS-250 specifications

HoMedics PS-250 is a state-of-the-art personal ultrasonic skin cleansing device that has gained popularity for its effectiveness in promoting healthy skin. This innovative device is designed to cater to a wide range of skin types and concerns, making it a versatile addition to any skincare routine.

One of the main features of the HoMedics PS-250 is its advanced ultrasonic technology, which operates at a frequency of 24,000 Hz. This high-frequency vibration gently exfoliates the skin while deeply cleansing pores, effectively removing dirt, oil, and makeup residue. This process not only helps to prevent breakouts but also prepares the skin for enhanced absorption of skincare products.

The PS-250 features two primary modes: cleansing mode and serum infusion mode. The cleansing mode utilizes the ultrasonic vibrations to provide a deep clean, while the serum infusion mode allows users to apply their favorite serums or moisturizers. By using the ultrasonic waves in this mode, the device helps to increase the penetration of active ingredients, maximizing the benefits of skincare products.

Another notable characteristic of the HoMedics PS-250 is its user-friendly design. The device is lightweight and ergonomically shaped, allowing for easy handling during treatment sessions. It is also equipped with an LED indicator that informs users of the current mode and battery status, ensuring a seamless experience.

The device is rechargeable, offering the convenience of cordless use. A single charge provides sufficient power for multiple sessions, making it ideal for both home use and travel. Additionally, the PS-250 is designed to be waterproof, allowing for easy cleaning and hygiene maintenance.

HoMedics places a strong emphasis on safety and comfort. The PS-250 is crafted with high-quality materials that are gentle on the skin. Its advanced technologies ensure that users can enjoy the benefits of professional-level skincare in the comfort of their own home.

In summary, the HoMedics PS-250 is an innovative ultrasonic skin cleansing device equipped with advanced features, modes for cleansing and serum infusion, and a user-centric design. Its effectiveness in promoting healthier skin through deep cleansing and enhanced product absorption makes it a noteworthy addition to modern skincare regimens. With its emphasis on convenience and safety, the PS-250 stands out as a must-have tool for anyone looking to elevate their skincare experience.