Rowenta 1103897124 manual Additional functions, After ironing, Cleaning and maintenance, Problems?

The power steam and vertical steam functions (E 4) are also possible if the steam control is set to . The interval between bursts of steam should be about two seconds.

Important:

Never direct the steam at persons or animals!

E5 Spray function

To dampen stubborn creases, press the spray button.

F Additional functions

F1 Anti-Drip system

Prevents water escaping from the soleplate when the temperature is too low.

F2 Anti-scale system

Your iron contains an anti-scale cartridge to reduce scale deposits. This considerably prolongs the operational life of your iron. The anti-scale cartridge is an integral part of the water tank and need not be replaced.

Do not use descaling agents, as these damage the lining of the steam chamber and so may impair the steam function.

F3 Automatic electronic 3-position cut-out (depending on model)

If, although switched on, the appliance is not moved, it will automatically switch off after the following intervals:

After 30 sec., if the iron is standing on the soleplate or lying on its side.

After 8 mins., if the iron is standing on its heel.

The LED display starts to flash yellow-green-red in regular sequence. If the appliance is moved, it will automatically switch on again and begin to heat up again.

G After ironing

•Unplug from the mains, pour away remaining water and set steam control to . Then allow the appliance to cool down.

•Store the iron standing on its heel.

•Do not wind the cord round the hot soleplate.

H Cleaning and maintenance

When the appliance has cooled down, wipe it down with a damp cloth or sponge, as required.

Dirt can be removed from the soleplate with a damp cloth or sponge. Do not use sharp or abrasive cleaning agents or objects.

Important: If the appliance has been standing unused for long periods, hold it horizontal and allow it to emit steam for approx. 1 minute to clean the steam ducts and remove any residue from the iron.

4

I Problems?

Problems	Possible cause	Solution
The iron is plug-	No mains supply.	Check that the mains plug is
ged in, but the		properly inserted or try
soleplate of the		plugging the iron into a dif-
iron remains cold.		ferent socket.
The soleplate is	The temperature	Set the temperature control
not heating up	control is set too	to a higher temperature (D).
properly.	low.
LED „Traffic Light“	Temperature con-	Turn the temperature control
display does not	trol set to "0".	to the required setting.
light up.
None or too little	There is insuffi-	Fill the water tank (C).
steam is being	cient water in the
emitted.	water tank.
	Anti-Drip is active	Wait for the soleplate to reach
	(F1).	the correct temperature.
All 3 colours of	The automatic cut-	If moved, the appliance will
the Traffic Light	out has activated:	switch on again.
display flash	the appliance is
alternately.	on standby.
The traffic Light	The temperature	Call our Customer Relations
display flashes	sensor in the sole-	Helpline – see below
red fast.	plate is defective.
Brown streaks	You are using che-	Do not add any descaling
come through the	mical descaling	agents to the water in the
holes in the sole-	agents.	water tank.
plate and stain	You linen is not	Ensure linen is rinsed
the fabric.
	rinsed sufficiently	thoroughly to remove any
	or you have ironed	soap desposits or chemicals
	a new garment	on new garments which may
	before washing it.	be sucked up by the iron.
The soleplate is	You are using a too	See the temperature table to
dirty or brown	high temperature.	correctly set the thermostat.
and can stain the	You are using	Clean the soleplate as indi-
linen.
	starch.	cated above. Always spray
		starch onto the reverse side
		of the fabric to be ironed.
The soleplate is	You have placed	Always set the iron on its
scratched or	your iron flat on a	heel.
damaged.	metallic rest-plate.
	You have ironed	Try to avoid ironing over zips
	over a zip.	which may have rough edges.

If you have any further problems or queries with our products please call our Customer Relations team first for expert help and advice:

HELPLINE:0845 602 1454 – UK, 01 4751947 – Ireland

If you are unable to trace the cause of the fault, contact an official Rowenta Customer Service Centre. The addresses are shown in the enclosed service centre address list. Further hints

and tips are obtainable from our homepage: www.rowenta.com.
In line with a policy of continuous product improvement
Rowenta reserves the right to change product specifications
without prior notice.	5