Installation, Positioning | Tricity Bendix TM 210 W guide

Installation

Positioning

The appliance may be placed in any room, provided the following precautions are taken.

The appliance expels hot, very moist air. The rest of the house must be able to easily absorb this moisture. Normally, absorption is only possible in houses where there is very little humidity. Otherwise, the room must have ventilation towards the outside; generally, an open door or window is enough.

The capacity of the venting circuit must be at least 150 m3/hour. Check that the air inlet and outlet vents are unobstructed.

The best way of evacuating the moisture is through a vent hose to the outside of the building. Use a special 100 mm diameter flexible hose available on the market connected to one of the air outlet vents with the collar supplied.

The unused outlets must be covered.

Never connect the air vent hose into an existing discharge pipe or duct, as this could be dangerous, might disturb neighbours and could cause the dryer to malfunction.

Advice: If the hose is long and the room temperature low, the moisture might condense to water inside the hose. This is an unavoidable natural phenomenon. To prevent this water from lying in the hose or flowing back

Problems can be encountered in rooms fitted with a very powerful central extractor fan. If you find that drying times are too long, switch off the extractor or close its grille whilst the tumble dryer is in use.

A highly effective solution is to simply poke the vent hose through a window or skylight. This might however cause problems in winter because the dryer will draw in very cold (and often also very damp) air through the open window, so increasing drying times and leading to very high energy consumption.

If the dryer is fitted next to kitchen units, make sure that the vent hose is not squashed. If the hose is partially squashed, drying efficiency will be reduced, resulting in longer drying times and higher energy consumption.

If the hose is completely squashed, the safety cut-outs with which the machine is fitted may operate.

Condensation discharge through the vent hose

Condensation may be discharged either through a vent outlet provided at the back or through the left or right side outlet.

into the tumble dryer, it is advisable to drill a small hole (dia. 3 mm) in the lowest point of the hose and to place a small container below it. (See picture, point A).

Connect the other end of the hose to an opening in a door

P0330

The vent hose collar is placed in the rear vent outlet. Remove the collar by pulling it out of the vent outlet. Screw the collar to the vent hose.

Fit the hose into the required vent outlet, and place vent covers provided over the unused outlets.

P0751

or window. Fit a suitable shield or point the hose downwards to prevent any rain water and wind from getting in.

Rain and wind shields for placing over openings usually consist of valves or movable flaps. Periodically check the shield since strong winds and other factors (rust, dirt) can sometimes prevent it from opening, so causing problems with air venting.

If you use a rain shield, check that the openings in it are large enough to allow air to escape. Openings which are too small restrict the flow of air.

P0279S

P0055

The vent hose must not contain more than two bends when it is placed in position for operation.

You should NOT connect the flexible vent hose to, for example, a chimney or flue pipe designed to carry the exhaust from a fuel burning heating appliance.

TM 210 W specifications

The Tricity Bendix TM 210 W is a sophisticated and versatile kitchen appliance designed to meet the demands of modern cooking. Known for its user-friendly interface and energy efficiency, this model is a top choice for both amateur cooks and culinary enthusiasts. It combines practicality with advanced features, making it an essential addition to any kitchen.

One of the standout features of the TM 210 W is its spacious design. With a generous capacity, it allows users to prepare meals for large families or gatherings effortlessly. The appliance is equipped with multiple cooking functions, including grilling, roasting, and steaming, making it adaptable to a wide range of recipes. This versatility enables users to experiment with different cooking methods while achieving delicious results.

The TM 210 W utilizes advanced technology to ensure optimal performance. It is designed with precise temperature controls, allowing users to select the ideal cooking temperature for various dishes. This feature helps in achieving perfect results every time, whether it is baking a cake or roasting vegetables. Additionally, the model is equipped with an innovative timer function that alerts users when their food is ready, reducing the risk of overcooking.

Energy efficiency is another significant advantage of the Tricity Bendix TM 210 W. It is engineered to consume less energy compared to traditional cooking methods, which not only benefits the environment but also helps to lower electricity bills. This is especially important in today’s eco-conscious world where sustainability is a growing concern.

The design of the TM 210 W emphasizes practicality without sacrificing style. Its sleek white exterior complements a variety of kitchen decors, making it a visually appealing appliance. The control panel is intuitively designed, featuring clear buttons and indicators that make it easy for users to navigate through different settings.

In summary, the Tricity Bendix TM 210 W is a reliable and efficient kitchen appliance that offers a blend of functionality and modern technology. Its spacious capacity, multiple cooking functions, precise temperature control, and energy efficiency make it an ideal choice for anyone looking to elevate their cooking experience. With its stylish design and user-friendly interface, the TM 210 W stands out as a valuable asset in any kitchen setting.