Beko WM 5140 S, WM 5140 W manual Water Being taken Improper position

Page 27

The water

 

 

being taken

Improper position of the

Connect the water draining hose as described

in is directly

drain hose.

in the operation manual.

discharged.

 

 

No water can

This is not a problem. The

 

be seen in

 

water level is not visible

 

the machine

 

from the outside of the

 

during

 

machine.

 

washing.

 

 

 

 

Water level might be

 

 

above the lower level of

Run either the “Pump” or “Spin” program.

 

the door.

 

 

Machine might be heating

 

The door is

up the water or it may be

Wait until the process is over.

at the spinning cycle.

 

jammed.

 

Due to electrical safety

 

 

 

 

mechanism, the door can

 

 

only be opened a few

Wait until the process is over.

 

minutes after the program

 

 

has stopped.

 

Machine fills

 

 

with water

Inside of machine may be

For safety reasons, water should be cycled in

when a

hot.

and out a couple times.

process is

 

 

cancelled.

 

 

 

 

The machine will wait until there is a sufficient

 

Water pressure may be

amount of water, which may lengthen the

 

low.

washing time to avoid poor washing results due

 

 

to insufficient water.

 

Supply voltage may be

Washing time is lengthened to avoid poor

 

low.

washing results when the supply voltage is low.

 

Input temperature of

Cycle time lengthens to heat up the water when

 

the input water is cold. Also, washing time can

 

water may be low.

Washing time

be lengthened to avoid poor washing results.

 

 

The automatic spin correction system might

takes longer

 

than the time

 

have been activated due to the unbalanced

specified in the

 

distribution of the laundry in the drum.

manual

There may be an

The laundry in the drum may be clustered

 

(bundled laundry in a bag). Laundry should be

 

imbalance of laundry in

 

rearranged and re-spun.

 

the machine.

 

No spinning is performed when the laundry is

 

 

 

 

not evenly distributed in the drum to prevent

 

 

any damage to the machine and to its

 

 

environment.

 

Number of rinses and/

Water amount is increased to obtain a

 

or amount of rinse water

better rinse and a rinse cycle is added when

 

might have increased.

necessary.

27

EN

Image 27
Contents WM 5140 W WM 5140 S Please read this manual first Explanation of symbolsTable of Contents Overview Your Washing MachineSpecifications Intended use General SafetySafety instructions First UseIf there are children in your House Electrical connectionElectrical requirements Fitting a different plug Removing packaging reinforcement InstallationAppropriate installation location Adjusting the feetConnecting to the drain Connecting to the water supplyDisposing of the old machine Destroying the packaging materialInitial preparations for washing Sorting the laundryCorrect load capacity Detergent drawer Detergent, softener and other cleaning agentsLoading door Detergents and softenersEliminating lime formation SoftenerLiquid detergent StarchControl panel Selecting a Program and Operating Your MachineProgram selection Turning the machine onSpin Speed selection Program selection and consumption table Auxiliary functions Time delayChanging the program after the program has started Changing and canceling the time delayStarting the Program Progressing a programEnd of program Ending the program through cancelingAdding/removing laundry in standby mode Child-proof lockQuick instructions for daily use Outer cabinet and control panel Cleaning and careDetergent drawer Door and the drumDraining any remaining water and cleaning the pump filter Page Problem Cause Explanation / Suggestion TroubleshootingWater Being taken Improper position Case of a paused Washing Temperatures for a long Although prewash cycle is not selected, Items Button was Pressed Washing Start Page Guarantee Republic of Ireland ServiceService once the manufacturers guarantee has expired UK Mainland & Northern Ireland