Blomberg WNF 7341 A user manual

Page 29

Loading door cannot be opened.

Door lock is activated because of the water level in the machine. >>> Drain the water by running the Pump or Spin programme.

Machine is heating up the water or it is at the spinning cycle. >>> Wait until the programme completes.

Child lock is engaged. Door lock will be deactivated a couple of minutes after the programme has come to an end. >>> Wait for a couple of minutes for deactivation of the door lock.

Washing takes longer time than the one specified in the manual.

Water pressure is low. >>> Machine waits until taking in adequate amount of water to prevent poor washing quality due to the decreased amount of water. Therefore, the washing time extends.

Voltage might be low. >>> Washing time is prolonged to avoid poor washing results when the supply voltage is low.

Input temperature of water might be low. >>> Required time to heat up the water extends in cold seasons. Also, washing time can be lengthened to avoid poor washing results.

Number of rinses and/or amount of rinse water might have increased. >>>

Machine increases the amount of rinse water when good rinsing is needed and adds an extra rinsing step if necessary.

Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage. >>> Use recommended amount of detergent.

C Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.

Programme time does not countdown. (On models with display)

Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water.

Timer indicator will resume countdown after this.

Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected temperature.

Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum.

C Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.

Programme time does not countdown.

There might be an imbalance of laundry in the machine. >>> Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum.

C Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.

29

EN

Image 29
Contents Washing Machine Explanation of symbols Table of Contents Overview Your washing machineTechnical specifications General safety Important safety instructionsChildrens safety Intended usePage Appropriate installation location InstallationRemoving packaging reinforcement Removing the transportation locksConnecting to the drain Connecting water supplyElectrical connection Adjusting the feetFitting a different plug First useElectrical requirements Disposing of the old product Disposing of packaging materialTransportation of the product Things to be done for energy saving PreparationSorting the laundry Preparing laundry for washingLoading the laundry Correct load capacityUsing detergent and softener Using starch Using gel and tablet detergentUsing bleaches Using limescale removerSoiling Level Clothes Tips for efficient washingControl panel Operating the productPreparing the machine Programme selectionSpecial programmes Main programmesAdditional programmes Spin speed selection Temperature selectionProgramme and consumption table Auxiliary function selection Canceling the Delayed Start function Changing the Delayed Start periodStarting the programme Child LockLoading door lock Canceling the programmeChanging the selections after programme has started End of programmeCleaning the detergent drawer Maintenance and cleaningCleaning the loading door and the drum Cleaning the body and control panelDraining remaining water and cleaning the pump filter Page Tap is turned off. Open the inlet water taps fully TroubleshootingPage Select the proper temperature for the laundry to be washed Page Use smaller amounts of detergent for this type of item Page Guarantee Service once the manufacturers guarantee has expired ServiceBlomberg, 36-38 Caxton Way, Watford Hertfordshire, WD18 8UF